A 10×16 shed material list for a gable shed on skids is 124 2x4s (100 for framing, 24 for blocks, braces and stakes), 13 treated 2×6 joists, 4 skids, 6 sheets of 3/4 in plywood, 9 of OSB, 17 of T1-11 and 9 shingle bundles, for 94 1/2 in walls, a 6/12 roof and 12 in eaves.
Every quantity and cut length on this page comes from the shopping list, cut list and cutting plan in the 3DSHEDPLANS 10×16 gable shed plan PDF. The list below matches the plan: one 72 in double door, two 36 x 36 in windows and a detachable ramp.
What this 10×16 list assumes
The plan is a shed 10 ft deep and 16 ft wide, with 160 sq ft of floor and the ridge running the 16 ft way. These are its settings:
- Walls: 94 1/2 in tall including the bottom plate and double top plate, so wall studs are cut to 90 in (7′ 6″).
- Spacing: studs, floor joists and rafters all at 16 in on center.
- Roof: 6/12 pitch, 2×4 rafters, a 2×6 ridge board, 12 in eave overhang and 4 in rake overhang. The roof footprint to the fascia is 16′ 9 1/2″ by 12′ 1 1/2″.
- Floor: four pressure-treated 4×4 skids 16 ft long, 3′ 2 13/16″ on center, on a crushed stone pad over an 18′ x 12′ area inside a pressure-treated 4×6 frame, plus a landing in front of the door, with 2×6 joists cut to 9′ 9″ at 16 in on center and 3/4 in tongue and groove plywood.
- Loads: the 2×4 rafters pass a span table check at 30 psf ground snow (SPF #2 at 16 in, 60 in run). That is the plan’s design assumption; if your area’s snow load may be higher, check your local permit office before you buy rafter stock.
- Openings: a 72 in wide double door (76 1/2 in rough opening height) centered in the 16 ft front wall, from 5′ 0″ to 11′ 0″ off the left corner, and two windows, each a 36 x 36 in rough opening, one in each 10 ft side (gable) wall. The back wall has no openings.
- Heights: the deck sits 9 3/4 in above the ground, the walls top out at 8′ 8 1/4″ and the peak at 11′ 5 5/16″. The door has 6′ 5 1/4″ of clear height under the head stop.
- Ramp: a detachable pressure-treated ramp, 6′ 9″ wide and 3′ 6″ out from the door, at a 1:6 slope.
- Anchors: 6 screw-in ground anchors with straps, three along each outside skid.
- Time: the plan estimates about 64 hours for two people: 5 for the site and skids, 7 for the floor, 16 for the walls, 11 for roof framing, 13 for sheathing and shingles and 12 for the door, windows, trim and paint.
Our 10×16 gable shed plan is this exact build, so this page and the plan’s printable list match line for line.
Shopping list by stage: the full 10×16 shed material list
Lumber sizes are nominal. A 2×4 measures about 1 1/2 x 3 1/2 in, as the American Wood Council explains. Check the grade stamp on plywood and OSB; the APA trademark guide shows how to read it.
Totals at a glance
| Material | Total |
|---|---|
| 2×4 boards, all lengths (framing, seam blocks, braces, ridge post, stakes, cleats) | 124 |
| Pressure-treated 2×6 (13 joists, 2 rims; 4 more for the ramp) | 15 |
| Pressure-treated 4×4 x 16 ft skids | 4 |
| 2×6 (two ridge pieces, two window headers) and 2×8 x 14 ft (door header) | 4 and 1 |
| 3/4 in plywood / 7/16 in OSB / 5/8 in T1-11 / 1/2 in plywood | 6 / 9 / 17 / 2 sheets |
| 3-tab shingle bundles | 9 |
Foundation and floor
| Item | Qty | Used for |
|---|---|---|
| Pressure-treated 4×4 x 16 ft, tagged for ground contact | 4 | Skids |
| Pressure-treated 2×6 x 10 ft | 13 | Floor joists |
| Pressure-treated 2×6 x 16 ft | 2 | Rim joists |
| 3/4 in T&G plywood, 4×8 sheet | 6 | Floor decking |
| 2×4 x 8 ft | 2 | 12 flat seam blocks under the decking |
| Construction adhesive, 10 oz tube | 8 | Joist beads and door frame |
| Crushed stone 3/4 in, loose | 4.0 cu yd | Gravel pad and ramp landing, 4 in deep, measured loose before tamping |
| Pressure-treated 4×6 x 16 ft, ground contact | 5 | Pad frame |
| Pressure-treated 4×6 x 8 ft, ground contact | 1 | Pad frame |
| Rebar stakes 1/2 in x 24 in | 30 | Pad frame |
| Galvanized timber spikes 3/8 x 10 in | 16 | Pad frame corners |
| Ground anchors, screw-in auger type, 30 in or longer, with straps | 6 | Anchoring the skids |
| Structural wood screws 1 1/2 in, exterior | 36 | Anchor straps |
| Deck screws 2 in (or 6d ring-shank nails), rated for treated lumber | 4 lb | Decking |
Walls and roof framing
| Item | Qty | Used for |
|---|---|---|
| 2×4 x 8 ft | 55 | Wall studs, cripples, sills, gable studs, frieze blocks, the ridge splice cleat |
| 2×4 x 10 ft | 9 | Side wall plates and cap plates, collar ties |
| 2×4 x 12 ft | 12 | Rafter ties, gable vent sills and headers |
| 2×4 x 14 ft | 18 | 13 for rafters, 2 for fly rafters, 1 each for the door and window trimmers |
| 2×4 x 16 ft | 6 | Front and back wall plates and cap plates |
| 2×6 x 8 ft | 3 | Window headers (one board per window) and the 7′ 0″ ridge piece |
| 2×6 x 10 ft | 1 | The 9′ 8″ ridge piece |
| 2×8 x 14 ft | 1 | Door header |
| Hurricane ties, H2.5A type or equal | 22 | Rafter to plate |
| Framing angles, A34 type or equal | 4 | End rafters at the 4 corners |
| Temporary braces 2×4 x 12 ft | 12 | Two plumb braces and a squaring diagonal per wall section, reused later |
| Temporary braces 2×4 x 12 ft | 4 | Center gable stud braces |
| Temporary ridge post 2×4 x 12 ft | 1 | Holds the ridge joint until its rafter pair is nailed |
| 2×4 x 8 ft | 3 | 8 pointed brace stakes, 24 in each |
| 2×4 x 8 ft | 2 | 12 deck cleats, 12 in each |
The three header filler strips of 1/2 in plywood are ripped from a soffit sheet, so buy those sheets with the wall lumber. Add the 2 seam-block boards, 17 braces and ridge post and 5 boards for stakes and cleats to the 100 framing boards and the truck carries 124 2x4s in all. The plan also says to add 2 or 3 spare studs for bad boards.
Roof covering
| Item | Qty | Used for |
|---|---|---|
| 7/16 in OSB, 4×8 sheet | 9 | Roof sheathing |
| 15 lb felt, 400 sq ft roll | 1 | Underlayment |
| 3-tab shingles, 26 per bundle | 9 bundles | Roof, starter course and ridge cap |
| Drip edge, 10 ft | 8 | Eaves and rakes |
| Roofing nails 1 1/4 in galvanized | 7 lb | Shingles |
| Roofing cap nails 1 in | 2 lb | Felt |
| Roofing cement, 10 oz tube | 2 | Roofing |
| Louvered gable vent, 12 x 12 in | 2 | One in each gable |
| Under-eave vent 16 x 8 in, screened | 4 | Air in under the eaves, two per eave |
| Insect screen, 2 ft x 25 ft | 1 roll | Vent holes and gaps at the eaves |
Siding and trim
| Item | Qty | Used for |
|---|---|---|
| 5/8 in T1-11, 4×8 sheet | 13 | Walls |
| 5/8 in T1-11, 4×8 sheet | 2 | Gable triangles |
| 5/8 in T1-11, 4×8 sheet | 2 | Door leaves (one per leaf) |
| 1/2 in plywood, 4×8 sheet | 2 | Eave soffit and header fillers |
| Z-flashing, 10 ft | 2 | Wall siding to gable siding joint |
| Drip cap, 10 ft | 2 | Over the door and window head casings |
| 1×6 x 10 ft | 2 | Eave fascia (9′ 8″ piece per eave) |
| 1×6 x 8 ft | 6 | Eave fascia (7′ 0″ piece per eave) and rake fascia |
| 1×4 x 16 ft | 2 | Corner trim on the eave walls |
| 1×4 x 14 ft | 3 | Door casing sides, door stiles |
| 1×4 x 8 ft | 13 | Gable-wall corner trim, door head casing, window casings, door rails and Z braces |
| 1×2 x 8 ft | 2 | Door stop and astragal |
| Exterior paint and primer in one | 5 gal | Two coats, about 630 sq ft each (rough-sawn T1-11 soaks up more, so check the coverage on the can) |
| Exterior caulk | 3 tubes | Trim |
Ramp
| Item | Qty | Used for |
|---|---|---|
| Pressure-treated 2×10 x 8 ft | 2 | Stringer blanks (two 3′ 6″ blanks per board, two tapered stringers from each blank) |
| Pressure-treated 2×6 x 14 ft | 4 | 8 deck boards, 6′ 9″ each |
| Pressure-treated 2×4 x 8 ft | 1 | Ledger on the rim joist and skid |
| Exterior deck screws 3 in | 141 | Boards into the stringers |
| Structural screws 3 in, 1/4 in | 12 | Ledger into the rim joist and skid |
| Hook-and-eye latches, 4 in | 2 | Holding the ramp to its ledger |
| Anti-slip grit tape, 2 in x 15 ft | 4 rolls | One strip along each board |
Hardware and windows
| Item | Qty |
|---|---|
| Framing nails 3 1/2 in (16d), hot-dip galvanized (about 1,340 nails plus 10%) | 37 lb |
| Siding nails 2 1/2 in (8d), hot-dip galvanized | 16 lb |
| Sheathing nails 2 1/2 in (8d) for OSB | 7 lb |
| Connector nails 1 1/2 in for the ties | 3 lb |
| T-strap door hinges | 6 |
| Door handle and latch set | 1 |
| Barrel bolts for the fixed leaf | 2 |
| Carriage bolts 1/4 x 2 in with washers and nuts | 18 |
| Brush door sweeps, 36 in | 2 |
| Hold-open hook and eye, 10 in | 2 |
| Aluminum threshold cap, 6 ft | 1 |
| Exterior screws 1 1/4 in (door frame to T1-11) | 1 lb |
| Exterior screws 3 in (hinge straps into framing) | 1 box |
| Structural wood screws 5 in, exterior (tight wall corners) | 18 |
| Prefabricated window, 36 x 36 in rough opening | 2 |
| Flashing tape 4 in | 1 roll |
| Wood shims | 1 bundle |
Cut list highlights
Most of the 10×16 cut list is square cuts: 43 wall studs at 7′ 6″ (12 front, 15 back, 8 in each side wall), 13 floor joists at 9′ 9″ and four skids at a full 16′ 0″. The parts below have angles, overhangs, splices or stacked sizes.
| Part | Lumber | Cut length | Qty |
|---|---|---|---|
| Rafter (board length, see below) | 2×4 | 6′ 9 7/16″ | 26 |
| Fly rafter (rake) | 2×4 | 6′ 9 7/16″ | 4 |
| Ridge board (9′ 8″ + 7′ 0″) | 2×6 | 16′ 8″ overall | 1 |
| Rafter tie (interior pairs, at the plates) | 2×4 | 10′ 0″ | 11 |
| Collar tie | 2×4 | 4′ 10 9/16″ | 6 |
| Lookout block (rake overhang) | 2×4 | 2 1/2″ | 16 |
| Frieze block (over the eave walls, top beveled) | 2×4 | 1′ 0 1/4″ to 1′ 1 3/4″ (20 at 1′ 1″) | 24 |
| Door header (2×8 doubled + 1/2 ply) | 2×8 | 6′ 3″ | 2 |
| Door cripple (above the header) | 2×4 | 6 1/4″ | 5 |
| Door trimmer | 2×4 | 6′ 4 1/2″ | 2 |
| Window header (2×6 doubled + 1/2 ply), per window | 2×6 | 3′ 3″ | 2 |
| Window trimmer, per window | 2×4 | 6′ 6″ | 2 |
| Center gable stud (under the ridge) | 2×4 | 2′ 2 13/16″ | 2 |
| Gable end studs | 2×4 | 7 1/16″ to 2′ 7 1/16″, in 4 in steps | 2 each of 7 |
| Gable corner nailer (flat on the cap plate under each end rafter) | 2×4 | 9 5/8″ | 2 |
| Gable vent sill and header (flat) | 2×4 | 2′ 6 1/2″ | 4 |
| Gable vent side stud | 2×4 | 1′ 0″ | 4 |
| Front and back cap plate | 2×4 | 15′ 5″ | 2 |
| Side wall plate | 2×4 | 9′ 4 3/4″ | 4 |
| Side wall cap plate | 2×4 | 10′ 0″ | 2 |
Rafters. The 6′ 9 7/16″ figure is the board each rafter needs, measured along the board from the long point of the ridge plumb cut to the long point of the tail plumb cut, including the 12 in eave overhang. The top edge between the two plumb cuts is shorter, so do not lay out 6′ 9 7/16″ along the top edge. The list buys 18 boards at 14 ft: 15 of them carry two rafters each (13 for the 26 rafters, 2 for the 4 fly rafters) with about 4 7/8″ left over, and the other 3 give the six trimmers.
Mark the plumb cuts with a speed square pivoted to 6 on the common scale (26.6 degrees). The birdsmouth is a 2 1/2 in level seat and a 1 1/4 in plumb heel. That notch is 32 percent of the rafter’s depth, and the plan keeps it under one third, so do not cut it any deeper. Cut one pattern rafter, test it at both ends of the shed, then trace the other 25.
The 4 fly rafters hang off the 2 1/2 in lookout blocks and the ridge extension, not a wall, so they get the ridge plumb cut but no birdsmouth.
Ridge. The ridge is 16′ 8″, not 16′ 0″, because it runs 4 in past each gable wall to carry the fly rafters that make the rake overhang. That is longer than a 16 ft board, so the plan buys one 2×6 x 10 ft and one 2×6 x 8 ft and cuts the ridge as a 7′ 0″ piece at the left end and a 9′ 8″ piece. The joint is centered on the rafter pair 6′ 8″ from the left corner of the building, held on a temporary 2×4 post under the ridge until that pair is nailed.
Headers. The 72 in door opening gets a doubled 2×8 header (two 6′ 3″ pieces from one 14 ft board) with a 1/2 in plywood filler, on trimmers cut to 6′ 4 1/2″, with five 6 1/4″ cripples above it. Each window gets a doubled 2×6 header (two 3′ 3″ pieces) on 6′ 6″ trimmers, two 6 1/2″ cripples above, a 3′ 0″ sill and two 3′ 4 1/2″ cripples below.
Window placement. Each window sits in a 10 ft gable wall, whose plates run 9′ 4 3/4″ between the front and back walls. The plan places each opening clear of the center gable stud in the middle of the wall, which carries the ridge. Slide a window toward the middle and its header lands under that stud.
Gable studs. Each 10 ft gable gets seven studs plus the 2′ 2 13/16″ center stud, which is shorter than the tallest side stud because it stops under the deeper 2×6 ridge. The studs are laid out 16 in on center from one corner so the siding joints land on them, which puts the two halves of the gable out of step. That is why the list has seven lengths, one of each per gable, from 7 1/16″ to 2′ 7 1/16″. Four flat 2′ 6 1/2″ pieces and four 1′ 0″ side studs frame the two louvered vent openings in the gables. Measure each stud off your actual end rafter before cutting.
Plates. The front and back walls run 16′ 0″ at the bottom with 15′ 5″ cap plates, and the side walls run 9′ 4 3/4″ at the bottom with 10′ 0″ cap plates. The side caps lap over the front and back walls, which locks the corners together.
Gable vs lean-to: what changes
The gable column is the plan PDF. We also ran the same 10×16 footprint as a lean-to (single-slope) roof at 3/12 with a 72 in double door, an 80 in low back wall, the door in the high front wall and the window in the back wall. The skids, joists and decking stay the same; the studs, rafters and siding change. The lean-to column is taken from the rebuilt 10×16 lean-to plan PDF, including its ramp and ground anchors, which the gable column does not list.
| Item | Gable (6/12) | Lean-to (3/12) |
|---|---|---|
| Rafters | 26 2×4 at 6′ 9 7/16″ + 4 fly | 13 2×6 at 11′ 8 1/2″ + 2 fly |
| Ridge board | 2×6, 16′ 8″ in two pieces | None |
| Wall studs | 7′ 6″ on all four walls | 8′ 8 5/8″ front, 6′ 3 1/2″ back, stepped on the sides |
| 2×4 framing boards bought (seam blocks and braces not counted) | 100 | 52 |
| 2×6 boards bought (not treated) | 4 | 19 |
| T1-11 sheets | 17, all 4×8 | 16: six 4×10, two 4×9, eight 4×8 |
| Roof OSB sheets | 9 | 7 |
| Shingle bundles | 9 | 7 |
| Felt | 1 roll | 2 rolls, laid double below 4/12 |
| Fascia | 1×6 | 1×8 |
| Soffit plywood | 2 sheets | 1 sheet |
| Extra hardware | 2 Z-flashing, 2 gable vents | 4 twist straps at the wall corners |
| Floor | 4 skids, 13 joists, 6 sheets | 4 skids, 13 joists, 6 sheets |
The lean-to’s rafters span the full 10 ft, so they move up to 2×6: a 113 in span against a 143 in limit for 2×6 at 30 psf. That is why the lean-to buys far fewer 2x4s and far more 2x6s. Each side wall has 9 studs stepping about 4 in at a time, from 6′ 5 3/8″ to 8′ 9 3/16″, under a 9′ 8 1/4″ sloped top plate. The front and side walls need 4×9 and 4×10 siding sheets, which some yards have to order.
At 3/12, read the minimum slope on the shingle wrapper and follow the maker’s low-slope instructions; the lean-to list already buys the second roll of felt for a double layer. For single-slope layouts, see the 8×16 lean-to shed plan, all lean-to shed plans and our gable vs lean-to vs hip roof comparison.
Where the waste goes
- Wall studs: 90 in from a 96 in board leaves about 6 in each.
- Rafters: two 6′ 9 7/16″ rafters from each 14 ft board leave about 4 7/8″. Reject any board with a split end; that is little room to trim two rafter tails.
- Floor joists: 9′ 9″ from a 10 ft board leaves 3 in for squaring the ends.
- Rafter ties: the eleven 10′ 0″ ties come from 12 ft boards, leaving about 2 ft each. The plan buys three 8 ft boards for the 8 brace stakes, so keep these offcuts for spare stakes or blocking.
- Plates: the 15′ 5″ cap plates leave about 7 in and the 9′ 4 3/4″ side plates about 7 1/4″. The two 10′ 0″ side cap plates use a full 10 ft board with no trim room, so check that the factory ends are square before you set them.
- Ridge and eave fascia: each 16′ 8″ run is cut as 9′ 8″ from a 10 ft board plus 7′ 0″ from an 8 ft board, so expect about 4 in and 1 ft of offcut per run.
- Floor decking: 2 full rows cover 7′ 11″ of the 10 ft frame, because a tongue and groove sheet covers only about 47 1/2 in. The last row is 2′ 1″ wide, too wide for two rips from one sheet, so it comes as two full 8 ft strips from 2 more sheets, 6 in all. Each strip keeps the groove edge, and 12 flat 2×4 seam blocks (10 at 1′ 2 1/2″, 2 at 1′ 1 3/4″) carry the narrow row’s edges.
- No spares: the counts include nothing for rejects. The boards with no margin are the 16 ft skids, rims and front and back wall plates and the 10 ft side cap plates, so pick those by hand or buy one extra of each. Pick straight stock at the yard, and add a few 2×4 x 8 ft if you expect to cull warped or split boards.
The longest pieces are 16 ft: the skids, rims, front and back plates, two corner trim boards and five 4×6 pad frame boards. Those hang well past a pickup bed, so ask the yard to deliver.
Tools for a 10×16 build
- Circular saw for the 43 stud cuts and 30 rafters; cut the 2 1/2 in lookout blocks from a long clamped stick with a stop block, never as loose scraps
- Speed square, framing square and a chalk line for the rafter layout
- Framing hammer or framing nailer, and a drill/driver for the screws
- 4 ft level, 25 ft tape for checking the floor diagonals match, and a string line to check the 16 ft rims are straight
- A hand tamper (the plan’s tool list) or a rented plate compactor for 4.0 cu yd of gravel, tamped in two layers, and sawhorses that support 16 ft plates
- Two 8 ft step ladders, a 16 ft extension ladder for the 8′ 8″ eave, and one helper: the plan raises each wall as a bare frame with 2 people, the front wall at about 210 lb, the back about 190 lb and each side wall about 150 lb
Common mistakes
- Mixing up 10×16 and 16×10. In this list the ridge runs along the 16 ft side and the door sits in a 16 ft wall. Turn the ridge the other way and you get a 16 ft rafter span, which needs bigger rafters, a different ridge and much taller gables.
- Forgetting the door sheets. The siding cut out of the doorway is 76 1/2 in tall, shorter than the 77 1/4 in (6′ 5 1/4″) door stiles, so each leaf needs its own new T1-11 sheet.
- Skipping rafter ties. A ridge board is not a beam. The 11 rafter ties at the plates stop the 16 ft walls from spreading. The 6 collar ties, higher up on every other interior pair, hold the rafter pairs together near the ridge; they do not replace the rafter ties.
- Deep birdsmouths. A full 3 1/2 in seat would notch a 2×4 rafter past the plan’s one-third limit, so keep the seat at 2 1/2 in.
- Too few skids. The plan keeps skids no more than 48 in apart. Four under a 10 ft floor land 3′ 2 13/16″ on center; three would land about 58 in apart, past that limit.
- Swapping materials without recounting. This list is for 3-tab shingles and T1-11. Architectural shingles, metal roofing or lap siding cover differently, so recount from the coverage printed on the bundle or the maker’s install guide.
- Untreated wood near the ground. Skids, rims and joists are pressure treated; plain framing lumber there rots. Use ground-contact rated wood for the skids, and hot-dip galvanized nails and treated-lumber rated screws in treated wood. The USDA Wood Handbook covers why wet, untreated wood decays.
The list includes 6 screw-in ground anchors with straps; ask which anchor type your area accepts for a skid shed. Tie-downs, setbacks and whether a 160 sq ft shed needs a permit vary by town, so check your local permit office before you order. Our shed permit checklist lists what to ask.
For how to read any list like this one, see our shed material list guide. For the base under the skids, see shed foundation options. For a rough budget, see how much it costs to build a shed; price this list at two yards before you order.
Get the full plan
The 10×16 gable shed plan is a 68-page 3DSHEDPLANS PDF with 19 step-by-step build sections, the cut list, the cutting plan and the printable material list this page is taken from. It has the same 72 in double door, two 36 x 36 in windows and wheel-in ramp, and estimates about 64 hours for two people.
Prefer a roof that slopes on all four sides? See the 10×16 hip roof shed plan. For the nearest sizes, see the 10×14 gable shed plan and the 10×20 gable shed plan, or compare the 10×12 shed material list and the 12×16 shed material list.
Want to see the format first? Download the free 10×16 gable shed plan preview PDF. Need more or less room? Compare all gable shed plans or browse every size on the shed plans page.
Frequently asked questions
What is on a 10×16 shed material list?
The 3DSHEDPLANS 10×16 gable plan lists 124 2x4s incl. braces, 15 treated 2x6s, 4 treated 4×4 skids, 6 sheets of 3/4 in plywood, 9 of OSB, 17 of T1-11, 2 of 1/2 in plywood and 9 shingle bundles, plus the ramp, pad frame, nails and trim.
Is there a 10×16 shed plan with a materials list?
Yes. The 3DSHEDPLANS 10×16 gable shed plan is a 68-page PDF with 19 step-by-step build sections, a shopping list by stage and a cut list. This page walks through that list and the key cut lengths, and a free 10×16 preview PDF shows the format first.
How many 2x4s do I need for a 10×16 shed?
124 for the 10×16 gable plan: 100 framing boards (55 at 8 ft, 9 at 10 ft, 12 at 12 ft, 18 at 14 ft, 6 at 16 ft), 2 at 8 ft for floor seam blocks, 17 at 12 ft for braces and a ridge post, and 5 at 8 ft for stakes and cleats.
How many sheets of plywood, OSB and siding does a 10×16 shed need?
6 sheets of 3/4 in tongue and groove plywood for the floor, 9 sheets of 7/16 in OSB for the roof, 17 sheets of 5/8 in T1-11 for the walls, gables and door leaves, and 2 sheets of 1/2 in plywood for the soffit and header fillers.
Shed building guides
- 8×12 Chicken Coop Material List: Lumber, Sheets, Hardware
- 8×10 Chicken Coop Material List: Lumber, Sheets, Hardware
- 6×8 Chicken Coop Material List: Lumber, Sheets, Hardware
- 10×12 Chicken Coop Material List: Lumber, Sheets, Hardware
- 8×8 Goat Shelter Material List: Lumber, Siding, Metal
- 8×12 Goat Shelter Material List: Lumber, Siding, Metal




