DIY 14x24 Gable Storage Shed Plan

The full plan is $19.99: buy the 14×24 gable shed plan. To see the drawing style first, open the free 14×24 gable shed plan PDF.

14×24 shed plans: the numbers for a site check

Square the stakes to matching 27′ 9 7/16″ diagonals before the stone goes down, and mark the roof footprint, not just the walls, when you check the yard.

How the 14×24 shed plans go together

Building 24 ft long from 16 ft stock

The longest board on the list is 16 ft, so the skids, rims, plates and ridge are spliced where the plan says:

• Skids. Each 24 ft skid is a 16 ft and an 8 ft piece butted on the gravel, the joint under a floor joist, scabbed on both sides with a 3 ft pressure-treated 2×4 and kept 4 ft or more from the joint in the next skid.
• Rims. Each rim is cut 11′ 11 1/4″ + 12′ 0 3/4″ and breaks over a doubled joist.
• Second top plates. On the front and back walls each is 7′ 8 1/2″ + 15′ 8 1/2″, with its joint away from the section joint below, so each layer covers the other’s joint.
• Ridge. The 24′ 8″ 2×8 ridge is 11′ 0″ + 13′ 8″, the joint centered on the rafter pair 10′ 8″ from the left corner and held on a temporary 2×4 post, 11′ 1 1/4″ from the deck to the underside of the ridge, until that pair is nailed.

The nailed floor frame weighs about 710 lb, so the plan has you build it in place on the skids and square it there.

How the walls go up

Each wall is framed flat on the deck and raised as a bare frame, and the siding goes on after all four stand. Both 24 ft walls go up in two sections so that two people can raise each one.

• Hinge it. Drive two or three nails partly through the bottom plate into the deck at the tipping edge so the section pivots instead of sliding.
• Join the sections. Clamp the two joint studs flush and nail them every 12″, then the second top plate laps the joint by at least 4 ft on each side.
• Brace from outside. 12 ft 2×4 braces run to stakes about 5 ft out, keeping the deck clear for the next wall.
• Siding alone. Screw a straight 2×4 ledger to the floor frame at the siding’s bottom line, stand each sheet on it and nail it off.

What is on the 14×24 materials list

The shopping list is split by stage, so you can buy the floor first and the roof later, in the stock lengths that waste the least:

• Foundation and floor: 16 ft and 8 ft pressure-treated 4×4 skid pieces, splice scabs, 2×6 rims and 20 joists, and 12 sheets of tongue and groove plywood.
• Walls: 7′ 6″ studs, plates, a doubled 2×8 door header, doubled 2×6 window headers and 20 sheets of T1-11 for the walls.
• Roof: 42 2×6 x 10 ft boards for 38 rafters and 4 fly rafters, the 2-piece 2×8 ridge, 2×4 x 16 ft boards for 17 rafter ties and 9 collar ties, 14 sheets of OSB, 2 rolls of 15 lb felt, 17 bundles of shingles and 10 pieces of drip edge.
• Door, windows and trim: 3 T1-11 sheets for the gable ends and 2 for the door leaves, 6 T-strap hinges, a handle and latch, 2 prefabricated windows, 1×8 fascia, plywood soffit, 1×4 casing and corner trim, Z-flashing and 2 louvered gable vents.
• Hardware: nails by the pound, 38 hurricane ties, adhesive, flashing tape, drip cap, insect screen and 7 gallons of paint.

What you can fit in a 14×24 shed

• Three zones. The 6 ft door is centered in the 24 ft front wall, which leaves a 9 ft bay on each side of the aisle for shelving, bins or a bench.
• A bench with daylight. Each side wall has a window with its sill 3′ 1″ above the bottom plate, so a workbench fits under one end and storage at the other.
• Long items. Ladders, lumber and garden tools can hang along the 24 ft back wall instead of lying across the floor.
• Riding mowers: measure first. The leaves hang inside the 72″ opening, so the clear width is a little less. The deck sits 9 3/4″ up, so plan a sturdy ramp.

Stick-framed rafters vs trusses on a 14×24 gable roof

Many 14×24 plans use trusses. This 3DSHEDPLANS plan frames the roof with 38 2×6 rafters 16″ on center against a 2×8 ridge board, plus 4 fly rafters on the rakes, so two people can build it one pair at a time with no truss jig.

• One pattern. Cut one rafter with a 3 1/2″ seat and a 1 3/4″ heel, test it on both sides with a ridge-thick block, then trace the rest. Each rafter comes from its own 10 ft board.
• Ridge first. A 3′ 2 3/4″ center stud on each gable wall carries the ridge pieces while you set the end pairs, then the pair at the ridge joint.
• Ties. A 2×4 rafter tie sits on the plates beside each of the 17 interior pairs to stop the walls spreading, and 9 collar ties go on every other pair to hold the ridge together in wind.
• Venting. Air comes in through three screened 1″ holes in each beveled frieze block over the eave walls and leaves through a louvered vent in each gable.

In heavy snow or high wind areas, ask about loads and check your local permit office before you build.

Free 14×24 shed plan PDF vs the full plan

The free PDF shows how the plan is drawn and what the shed looks like. The full plan adds all 19 step sections, the splice lengths, the rafter and ridge marks, the gable siding cuts, the floor and roof sheet maps, the cut list and the complete shopping list. Every number comes from one 3D model, checked by 106 automatic checks before publishing.

Before you build a 14×24 gable shed

• Permits. At 336 sq ft and 12′ 7″ tall, this is a large shed, and rules on size, height and setbacks vary by town and HOA. Check your local permit office before you buy lumber.
• Skids. Use ground-contact rated pressure-treated 4x4s (UC4A or higher), set each one crown up, and raise a low skid with more gravel or treated shims, never untreated wood.
• Keep it dry. Leave 6″ or more between the siding and the soil or mulch, and check the roof, caulk and paint every spring.
• Materials. Store lumber flat and covered, since wet wood decays faster (USDA Forest Products Laboratory Wood Handbook). Check the stamp on each OSB sheet for its span rating (APA: OSB).

Tools and ladders the plan lists

Beyond a circular saw, drill/driver and framing hammer, the tool list adds a miter saw for the door braces and trim, a reciprocating saw for the threshold cut, two bar clamps for marking the rims, a 3 lb sledge for the brace stakes and a hand tamper for the pad. Two 8 ft step ladders reach the ridge, and a 16 ft extension ladder covers roof work from the eave, about 8′ 8″ up.

Related plans

• 2 ft deeper: the 16×24 gable shed plan. 2 ft shallower: the 12×24 gable shed plan.
• 4 ft shorter and 2 ft deeper: the 16×20 gable shed plan.
• Same 24 ft length with a hip roof: the 16×24 hip roof shed plan.
• Choosing a base first? Read the shed foundation guide.
• Every gable shed plan in one place.