DIY 10x24 Gable Storage Shed Plan

The full plan is $19.99: buy the 10×24 gable shed plan. To see the drawing style first, open the free 10×24 gable shed plan PDF, an 8-page preview.

10×24 shed plans: the numbers for a site check

Square the corner stakes to matching 26′ 0″ diagonals before the gravel goes down, and check the pad frame to 28′ 7 5/8″ diagonals. Mark the roof footprint, not just the walls, when you measure your yard. The ramp and landing reach out in front of the door, so leave room there.

How the 10×24 shed plans go together

Building 24 ft long from shorter stock

No 24 ft board is on the list, so the skids, rims, plates and ridge are spliced where the plan says:

• Skids. Each 24 ft skid is a 16 ft and an 8 ft piece butted on the gravel, the joint under a floor joist. The skids alternate end for end, so the joints fall at 8 ft and 16 ft from the left end, 8 ft apart, each scabbed on both sides with a 3 ft pressure-treated 2×4 and six nails per scab.
• Rims. Each rim is cut 11′ 11 1/4″ + 12′ 0 3/4″ and breaks over a doubled joist, so both rim ends get nails into a full joist.
• Wall plates. The back wall plates break at 12′ 0 3/4″ from the right corner and the front wall plates at 15′ 11 1/4″ from the left corner, one joint per wall. The second top plate bridges each section joint and lands its own joint on a different stud, so each layer covers the other’s joint.
• Ridge. The 24′ 8″ 2×6 ridge is 11′ 0″ + 13′ 8″, the joint centered on the rafter pair 10′ 8″ from the left corner and held on a temporary post, 10′ 1 5/16″ long, until that pair is nailed and a cleat goes under the joint.

The nailed floor frame weighs about 530 lb and racks out of square if you lift it, so the plan has you build it in place on the skids and square it there to matching 26′ 0″ diagonals.

How the walls go up

Each wall is framed flat on the deck and raised as a bare frame, and the siding goes on after all four stand. Both 24 ft walls go up in two sections so that two people can raise each one.

• Hinge it. Stop blocks nailed to the outside of the rim keep the bottom plate from kicking out over the deck edge as the wall tips up.
• Brace at once. Never leave a raised wall unbraced, even for a minute, and never raise one in gusty wind.
• Siding. A 4×8 sheet of 5/8″ T1-11 weighs about 60 lb. Screw a straight 2×4 ledger to the floor frame at the siding’s bottom line, stand each sheet on it, and have a helper hold it plumb while you tack the top corners.

What is on the 10×24 materials list

The shopping list is split into sections, so you can buy the foundation and floor first and the roof later, in the stock lengths that waste the least. A cut list gives the length and count of every part.

Buy a few spare studs for bad boards. The temporary braces and the ridge post are on the list and can be reused after the build.

What you can fit in a 10×24 shed

The plan includes a to-scale drawing of one way to fill the floor:

• A riding mower. The 72″ double door gives a clear width of about 5′ 11 1/2″ with both leaves open, so a 42″ deck clears each side by 8 1/8″. A 48″ deck fits with its deflector raised, and a 54″ deck does not.
• Back-wall shelves. The 24 ft back wall has no opening, so 12″ deep shelves can run its length, split at the mower’s nose.
• Yard gear. A wheelbarrow and two bikes fit on the open floor beside the mower, with a 3′ 6″ cross aisle behind its tail.
• Light on both sides. The two 3 x 3 ft windows sit in the side walls, one on each end of the shed.

The ramp, door and windows in the 10×24 plan

• Door. The 72″ double door is built from two new T1-11 sheets, each leaf 2′ 11 5/8″ wide and 6′ 5 1/4″ tall, hung on 6 T-strap hinges with 2 barrel bolts and a hook and eye per leaf. The plate is cut out so the opening runs to the floor, and an aluminum threshold cap and brush sweeps seal the bottom.
• Ramp. The detachable ramp is 6′ 9″ wide and 3′ 6″ out at a 1:6 slope, so wheels roll on at a beveled toe and meet only a 13/16″ lip at the door. Unhook it and lift it away when you want the step back.
• Windows. Both windows are prefabricated units set in 3′ 0″ x 3′ 0″ rough openings, with the sill 3′ 6″ above the bottom plate.

Stick-framed rafters vs trusses on a 10×24 gable roof

Many free 10×24 plans use trusses you assemble on the ground. This 3DSHEDPLANS plan frames the roof with 38 2×4 rafters 16″ on center against a 2×6 ridge board, plus 4 fly rafters on the rakes, so two people can build it one pair at a time with no truss jig. Cut one rafter, test it on both sides, then trace the rest.

• Ridge first. A center stud on each gable wall carries the ridge while you set the end pairs, then the pair at the ridge joint, then the rest.
• Ties. A 2×4 rafter tie sits on the plates beside each of the 17 interior pairs to stop the walls spreading, and 9 collar ties hold the ridge together in wind. Keep anything stored on them light, since the plan does not build a loft.
• Venting. Air comes in through 8 screened 16″ x 8″ soffit vents, 4 under each eave, over a 1 1/2″ screened slot above the frieze blocks, and leaves through a 12″ x 12″ louvered vent in each gable. The plan prints the arithmetic: 248.2 sq in in all against a common attic rule of thumb of 230.4 sq in (240 / 150), which is not a shed requirement. The gable side alone comes out 36.0 sq in short of its half.

In heavy snow or high wind areas, ask about loads and check your local permit office before you build.

Free 10×24 shed plan PDF vs the full plan

The free 8-page PDF shows the shed, the stages of the build and the 3D views, so you can see the drawing style. It has no shopping list, cut list or measurements. The full 72-page plan adds the material list, the cut list, the cutting plan, the sheet maps and every build step with every dimension.

Before you build a 10×24 gable shed

• Permits. At 240 sq ft and 11′ 5 5/16″ tall, this shed is over the common 120 and 200 sq ft exemptions and may need a permit or meet setback limits, and rules vary by town and HOA. Check your local permit office before you buy lumber.
• Skids. Use ground-contact rated pressure-treated 4x4s (UC4A or higher), set each one crown up, and raise a low skid with more gravel or treated shims, never untreated wood.
• Anchors. An empty shed on skids can slide in a strong gust, so the plan adds 10 screw-in ground anchors with steel straps along the two outside skids.
• Materials. Store lumber flat and covered, since wet wood decays faster (USDA Forest Products Laboratory Wood Handbook). Check the stamp on each OSB sheet for its span rating (APA: OSB).

Tools for the 10×24 gable shed

Beyond a circular saw, drill/driver and framing hammer, the tool list adds two 8 ft step ladders, a 16 ft extension ladder for the roof, a 3 lb sledge for the brace stakes and rebar, and a hand tamper for the pad. Shingle bundles weigh 60 to 80 lb, so ask the supplier to deliver them onto the roof if they offer it.

Related plans

• 4 ft shorter: the 10×20 gable shed plan, or the 10×16 gable shed plan.
• Same length, 2 ft deeper: the 12×24 gable shed plan, or 4 ft deeper, the 14×24 gable shed plan.
• A single-slope roof on a 24 ft shed: the 12×24 lean-to shed plan.
• Choosing a base first? Read the shed foundation guide and the guide to building a shed roof.
• Every gable shed plan in one place.