Gable roof · 252 sq ft
14x18 Gable Storage Shed Plan
Build this 14x18 gable shed yourself. Every board, cut and step, drawn in 3D across 73 pages.
- 30-day money-back guarantee
- PDF by email right after checkout
- Visa, Mastercard, Amex, PayPal
- Full material and shopping list
- Cut list with every length
- Step-by-step 3D views, 73 pages
- Phone, tablet, PC and Mac

These 14x18 shed plans from 3DSHEDPLANS build a 252 sq ft gable storage shed on five 4x4 skids, 18 ft wide and 14 ft deep, with a 6 ft double door centered in the front wall, two 3x3 ft windows, a wheel-in ramp and a 6/12 roof. The PDF has 73 pages with the shopping list and cut list.
Get the full plan PDF for $19.99 or download the free preview
What builders say
A project for me and my son. The plan arrived in my email almost instantly, and everything we needed was included.
We aren't DIY-savvy and needed something simple. The plan was extremely well laid out and easy to follow.
A year ago I had only built flat-pack furniture. The plans are simple to follow, and you don't need years of experience.
The full plan is $19.99: buy the 14×18 gable shed plan. To see the drawing style first, open the free 14×18 gable shed plan PDF.
14×18 shed plans: the numbers for a site check
| Check | 14×18 Gable Shed |
|---|---|
| Walls | 18′ wide x 14′ deep, 252 sq ft of floor |
| Roof | 6/12 gable (26.6 deg), 12″ eaves and 4″ rakes, ridge running along the 18 ft front and back walls |
| Roof footprint | 18′ 9 1/2″ x 16′ 1 1/2″ to the fascia faces |
| Gravel pad | 20′ 0″ x 16′ 0″ in a pressure-treated 4×6 frame, 5.5 cu yd of stone, plus a landing in front of the door |
| Floor height | Top of the deck 9 3/4″ above the ground |
| Wall height | 7′ 10 1/2″ (7′ 6″ studs), top of the walls 8′ 8 1/4″ above the ground |
| Overall height | 12′ 7 1/16″ above the ground |
| Inside | 17′ 5″ x 13′ 5″, clear height 7′ 7 1/2″ under the top plates |
| Door | One 72″ x 76 1/2″ double door centered in the 18 ft front wall |
| Windows | 2, each 36″ x 36″, one in each 14 ft side wall near the front |
| Back wall | No openings, for shelves |
| Ramp | Detachable, pressure-treated, 6′ 9″ wide, 3′ 6″ out, 1:6 slope |
| Crew | Two people |
Mark the roof footprint and the gravel pad on your lot, not just the 18 by 14 ft walls, and leave room on every side to stand a ladder. The ridge runs the 18 ft length, so the front and back walls carry the eaves and the 14 ft side walls carry the gables.
How the 14×18 shed plans go together
| Part | What the plan uses |
|---|---|
| Site and foundation | Five pressure-treated 4×4 skids, 18 ft long and spliced, on a gravel pad in a pressure-treated 4×6 frame |
| Floor frame and deck | Pressure-treated 2×6 joists about 15 7/16″ on center, 3/4″ tongue and groove plywood, 10 sheets |
| Anchors | 8 screw-in ground anchors with straps, set before the walls go up |
| Walls | 2×4 studs 16″ on center or closer, raised as bare frames, then sided with 5/8″ T1-11 |
| Roof framing | 30 2×6 rafters against a spliced 2×8 ridge, rafter ties, collar ties and gable plate ties |
| Roofing | 7/16″ OSB sheathing, 15 lb felt, drip edge and 3-tab asphalt shingles |
| Door, windows and trim | A double door, two prefabricated windows, fascia, soffit, vents, paint and the ramp |
The plan runs in 19 step sections, from preparation and ground breaking through to the ramp, with a 3D view at the end of each step and a printable checklist to tick off each stage.
How long a 14×18 shed takes to build
The plan gives a typical time for two people at each stage:
| Stage | Typical time for 2 people |
|---|---|
| Site and foundation | 8 h |
| Floor frame and deck | 10 h |
| Walls: raise bare frames, then side them | 25 h |
| Roof framing | 17 h |
| Sheathing, felt and shingles | 21 h |
| Door, window, trim and paint | 19 h |
That adds up to about 100 hours, so plan it across several weekends. Weather, a sloped yard and the pace of your helper all move the number.
Site layout and the gravel pad
Stake the shed corners 18′ 0″ along the front and 14′ 0″ along the sides, then move one stake until both diagonals read 22′ 9 5/8″. On a sloped yard the plan has you run a string with a line level from the highest stake to the others first. A few inches of fall gets made up with deeper stone on the low side, compacted every 2″; more than that means digging the high side down or setting solid blocks on the low side.
The dig is 4″ deep over a 20′ 11″ x 16′ 11″ area, plus a strip in front of the door for the ramp and a 3 ft landing, 9′ 8″ wide and reaching 7′ 2 1/2″ out from the front wall. Pressure-treated 4x6s laid flat frame the pad, joined at each corner with two 10″ timber spikes and pinned with 36 rebar stakes. The inside of the frame is the 20′ 0″ x 16′ 0″ pad, square when its diagonals both read 25′ 7 3/8″, plus a landing 8′ 9″ wide. Inside goes 4″ of 3/4″ crushed stone, tamped in two layers, so the frame, the stone and the lawn finish level. Our gravel shed foundation guide explains why a pad like this drains.
Foundation: five spliced skids
An 18 ft skid is longer than a 16 ft board, so each of the five pressure-treated 4×4 skids is spliced from two pieces:
- Skids 1, 3 and 5 (counting from the front): 10′ 3 7/16″ + 7′ 8 9/16″ from the left end.
- Skids 2 and 4: 5′ 1 11/16″ + 12′ 10 5/16″ from the left end.
- Joints: each one centered under a floor joist and at least 4 ft from the joint in the next skid, scabbed on both sides with a 3 ft pressure-treated 2×4 and six nails per scab.
The skids run along the 18 ft side, 3′ 5 1/8″ on center, with the outer two flush with the floor edges. Everything that touches the gravel is rated for ground contact (UC4A or higher). Level each skid along its length, then all five to each other with a straight board.
Floor frame and decking
The two 2×6 rim joists are spliced too, from 8′ 11 1/4″ and 9′ 0 3/4″ pieces, and both break over a doubled joist so each rim end gets a full joist to nail into. Fifteen joists at 13′ 9″ sit about 15 7/16″ on center, evenly spread and mirrored about the middle, with the marks given in inches from the left end.
The nailed frame weighs about 560 lb and racks out of square if you lift it, so you build it in place on the skids. Square it by its diagonals, both 22′ 9 5/8″, before you fasten it down. Then a framing angle goes at every place a joist crosses a skid, 80 in all, with 8 connector nails each.
Ten sheets of 3/4″ tongue and groove plywood cover the floor, glued and screwed, laid from a lettered piece map with staggered end joints. Three full rows cover 11′ 10 1/2″ of the 14 ft depth, and the last row is a 2′ 1 1/2″ rip with flat 2×4 blocks under its seam so the narrow strip does not flex. Our shed floor framing guide covers the general method.
Anchoring the shed before the walls
The plan anchors the floor right after the decking, before any wall goes up. Empty, a shed this tall on loose skids slides at about 13 psf of wind, gusts near 60 mph, and tips at about 28 psf, and the bare walls catch that wind for days before the roof is on.
- Eight anchors. Screw-in auger anchors, 30″ or longer and galvanized, four along each outside skid at 1′ 0″, 6′ 4″, 12′ 1″ and 17′ 0″ from the left end.
- Through the stone. An auger will not start in compacted stone, so you dig back to the soil beside the skid at each spot, turn the anchor in with a steel bar, then rake and tamp the stone back.
- Straps. Each strap runs up the skid’s outside face onto the rim joist, held with four 1 1/2″ structural screws in the skid and two in the rim, ending below where the siding comes down.
Check your local permit office for what your area asks for anchoring.
Walls: raised in sections by two people
Each wall is framed flat on the deck and raised as a bare frame. The 18 ft walls would be too heavy for two people in one piece, so the plan splits them:
| Wall | How it goes up | Weight |
|---|---|---|
| Back wall | 2 sections, 9′ 7 1/4″ + 8′ 4 3/4″, 17 studs | About 110 lb and 100 lb |
| Front wall | 2 sections, 13′ 0 3/4″ + 4′ 11 1/4″, 15 studs | About 170 lb and 70 lb |
| Left wall | One piece, 13′ 4 3/4″ plates, 11 studs | About 190 lb |
| Right wall | One piece, 13′ 4 3/4″ plates, 11 studs | About 190 lb |
Every wall has a stud position table, the diagonals to square each section, and where to tack its diagonal brace. The second top plate laps each corner and bridges each section joint by at least 4 ft on each side, tying the walls together.
- Hinge it. Stop blocks on the rim keep the bottom plate from kicking out over the deck edge.
- Brace at once. Never leave a raised wall unbraced, even for a minute, and never raise one in gusty wind.
- Corners from inside. The corners are screwed from inside with 3″ exterior screws every 12″, since a hammer will not swing in the narrow corner bays.
- Siding last. T1-11 sheets go on once all four walls stand, one wall at a time, each sheet hung from a 2×4 ledger so your helper only has to hold it plumb.
Door, windows and ramp: sizes and positions
The door rough opening is 6′ 0″ wide and 6′ 4 1/2″ tall, from 6′ 0″ to 12′ 0″ measured from the left corner, under a header of two 2x8s with 1/2″ plywood between them. Once the bottom plate is cut out the opening is 6′ 6″ framed and 6′ 5 1/4″ clear under the head stop. With both leaves open the opening is about 5′ 11 1/2″ clear.
The two leaves are built from new T1-11 sheets, each 2′ 11 5/8″ x 6′ 5 1/4″, with a 1×4 frame and two Z braces on the outside face. Each hangs on three heavy T-strap hinges, held with carriage bolts so nobody can unscrew the door from outside. The left leaf is the active one with the latch; the right leaf is held by two barrel bolts on its astragal. An aluminum cap covers the deck edge, brush sweeps close the gap under the leaves, and hold-open hooks 36″ up keep wind from slamming the door. Our guide on how to build shed doors covers the same method.
The two windows are prefabricated 36″ x 36″ units, one in each 14 ft side wall, 1′ 11″ from the front end of the plate, each with its sill 3′ 6″ above the bottom plate and a header of doubled 2×6 at 3′ 3″. The back wall has no window, so the shelves have the whole wall.
The ramp is detachable pressure-treated lumber, 6′ 9″ wide and 3′ 6″ out at a 1:6 slope (9 deg). Eight stringers at 11 3/8″ on center carry eight 2×6 boards with grit tape, and the top sits about 13/16″ below the deck, so wheels roll in over a small lip with no threshold board. Two hook-and-eye latches hold it, so you can unhook it when you need to level or move the shed. Our guide on how to build a shed ramp explains the idea.
What is on the 14×18 shed material list
The shopping list covers every stage, so you can buy the foundation and floor first and the roof later. The plan does not price the list, since costs change by region. Take it to your local yard for a quote.
| Section | What the plan lists |
|---|---|
| Foundation and floor | 9 pressure-treated 4x4s for 5 spliced skids, pressure-treated 2×6 rims and 16 joists, 10 sheets of 3/4″ tongue and groove plywood, 80 framing angles |
| Pad | A pressure-treated 4×6 frame, 36 rebar stakes, 16 timber spikes and 5.5 cu yd of stone |
| Walls | 2×4 studs and plates, a 2×8 door header and 2×6 window headers, 18 sheets of T1-11 siding, 3 pieces of Z-flashing |
| Roof framing | 30 2×6 rafters plus 4 fly rafters, a 2×8 ridge, 13 rafter ties, 7 collar ties, gable plate ties, 26 hurricane ties and framing angles |
| Roof covering | 13 sheets of OSB, 28 H-clips, 9 pieces of drip edge, 2 rolls of felt and 13 bundles of 3-tab asphalt shingles |
| Fascia, soffit and gables | 8 1×8 boards for fascia, 3 sheets of T1-11 for the gables, 2 sheets of 1/2″ plywood for the soffit |
| Door, windows and trim | 2 more T1-11 sheets for the leaves, 6 T-strap hinges, latch, sweeps, hooks, 2 prefabricated windows, 1×4 casing and corner trim |
| Vents | 2 louvered 14″ x 24″ gable vents and 6 under-eave soffit vents |
| Ramp | Pressure-treated 2×10 stringer blanks, 2×6 deck boards, the ledger, 145 deck screws, latches and grit tape |
| Hardware | 46 lb of framing nails, siding, sheathing and roofing nails, 8 ground anchors with straps, 6 gallons of paint and primer, caulk |
At the end, a lumber yard order adds up every board and sheet from all the sections into one list you can hand to the yard.
Cut list and cutting plan
The cut list names every part with its lumber, exact length and count, from the 18′ 0″ skids down to the 2 1/2″ lookout blocks. The cutting plan then shows which board each part comes from and how many cuts it gives, so useful offcuts become cripples, lookouts and gable studs instead of waste. Parts the plan does not buy separately are marked with the offcut they come from.
Sheet goods get the same treatment. The floor, the roof and every wall have a lettered piece map, with a note on which pieces share a sheet, so you do not run short on the last row.
What you can fit in a 14×18 shed
The plan includes a to-scale drawing of one way to fill the 17′ 5″ x 13′ 5″ floor:
- A riding mower. A mower with a 42″ deck, 4′ 7 3/16″ x 5′ 10″, goes in nose first through the double door and clears each side by 8 1/8″. A 48″ deck fits with its deflector raised, and a 54″ deck does not.
- A walkable aisle. The drawing leaves a 5′ 6″ aisle behind the mower, running to the 24″ deep shelves along the back wall.
- Side shelves. The back 6 ft of each side wall takes 16″ deep shelves.
- A bench and the rest. A 20″ deep bench fits under the right window, with a wheelbarrow, 2′ 2″ x 5′ 0″, and two bikes with staggered handlebars, 2′ 6″ x 5′ 10″.
Keep 10′ 0″ clear and level out from the front wall, the ramp plus one mower length, to line a tractor up square. Shelves are yours to add. Our guide on what size shed fits a riding mower explains how to measure your own.
How the 14×18 gable roof is framed
At 6/12 the rafters rise 3′ 10″ from the top of the walls to the top of the ridge. You cut one pattern rafter from the straightest 2×6, with a birdsmouth seat 3 1/2″ long and a heel 1 3/4″ high, test it on both sides, then trace the rest: 30 rafters at about 15 7/16″ on center plus 4 fly rafters for the rakes. Each rafter takes its own 10 ft board.
- Ridge in two pieces. The 2×8 ridge is 18′ 8″, spliced from two 9′ 4″ pieces, so no board on the list is longer than 16 ft. The joint is centered on the rafter pair 9′ 0″ from the left corner. A temporary post holds the joint until its rafter pair is in, a center gable stud on each gable wall holds each end, and a 24″ cleat ties the joint once the post comes out.
- Rafter order. Set the end pairs first, then the pair at the ridge joint, check the ridge for level and center, then fill in the pairs between.
- Rafter ties. 13 ties of 2×4, each 14′ 0″ long, sit on the plates beside the interior pairs and stop the walls from spreading.
- Collar ties. 7 collar ties, 6′ 4 7/8″ long with both ends cut along the roof slope, hold the rafters together at the ridge in wind.
- Gable plate ties. Flat 2x4s tie each gable wall plate to the first rafter ties and stiffen the top of the end walls.
- Hurricane ties. The 26 inside rafters get a hurricane tie at the plate, and the 4 end rafters a framing angle at each corner.
Gable end studs stand under each end rafter, notched over it, with a table of their long-point lengths. Our shed roof pitch guide explains what 6/12 means for headroom and runoff.
Roof covering, siding and trim
The roof deck is 13 sheets of 7/16″ OSB, laid from a lettered map with 1/8″ gaps. The top row on each side is a narrow 10 3/16″ strip, so 28 H-clips carry its seam. Drip edge goes on the eaves under the felt and on the rakes over it. Two rolls of 15 lb felt run from the eave up, then about 320 shingles, 13 bundles, cover the roof in 21 courses a side at 5″ exposure, starter strips and 46 ridge cap pieces included.
Shingle bundles weigh about 60 to 80 lb, so the plan has you carry half a bundle at a time or ask the supplier to deliver them onto the roof. It also has you screw a 2×4 foot stop into the rafters a foot above the eave before you work above it, and never work on the roof alone.
The walls take 18 sheets of 5/8″ T1-11, the gables 3 more, and the door leaves 2 new sheets. Z-flashing joins the wall siding to the gable siding. Trim is 1×4 on every corner and around the windows, with a drip cap over the door and window heads, flashing tape around each window opening, and caulk on the trim joints before paint.
Vents and the rake overhang
Air comes in at the soffit through 3 vents per eave and a 2″ screened slot over each frieze block, and leaves through a 14″ x 24″ louvered vent in each gable, set in a framed 1′ 3″ x 2′ 0″ opening under the ridge. The plan adds it up: 184.8 sq in of high vent area and 143.0 sq in of low vent area, 327.8 sq in in all. A common attic rule of thumb, which the plan notes is not a shed requirement, asks for 242 sq in on a floor this size, about half low and half high. Our shed ventilation guide explains why that path matters. Lookout blocks carry the fly rafters 4″ out on each rake.
Tools, ladders and fasteners
The plan lists the tools for each stage, including a 16 ft extension ladder that reaches about 4 ft past the eave when set at the right angle, and a steel bar for turning the ground anchors. A fastener schedule gives the nail or screw, spacing and count for every joint, from three 3 1/2″ nails per joist at the rim to four roofing nails per shingle. Ladder and roof safety steps sit at the front of the plan, before the first cut.
What the 116 checks cover
The back of the plan lists what was checked before it went on sale:
| What was checked | Checks | Result |
|---|---|---|
| Walls and openings | 61 | All pass |
| Floor and foundation | 6 | All pass |
| Roof framing | 20 | All pass |
| Sheet goods and roofing | 6 | All pass |
| Drawings agree with the lists | 6 | All pass |
| Board lengths and offcuts | 1 | All pass |
| Trim, soffit, section and other checks | 16 | All pass |
The checks cover the framing closing, the roof geometry, the sheets and shingles covering every surface, no two framing members overlapping, and the drawings, tables and lists agreeing with each other.
Free 14×18 shed plan PDF vs the full plan
The free 8-page PDF shows the drawing style, the five build stages and the finished shed before you pay. It has no material list, no cut list and no dimensioned drawings. The full 73-page plan adds the shopping list, the cut list, the cutting plan, every wall drawn stud by stud, the rafter and ridge details and all the build steps with every dimension. Before it went on sale every measurement was cross-checked with 116 checks, and all of them pass.
Before you build a 14×18 gable shed
- Permits. At 252 sq ft and over 12 ft tall, this shed may run into size, setback or height limits, and rules vary by town and HOA. Check your local permit office before you buy lumber; our shed permit checklist lists what to ask. Call 811 a few working days before you dig.
- Snow and wind. The plan uses common small-shed framing and is not an engineered design. In heavy snow or high-wind areas, ask about rafter size, spacing and ground anchors before you build.
- Keep it dry. Leave 6″ or more between the siding and the soil, and every spring check for lifted shingles, re-caulk the trim and make sure the skids are still level and dry.
- Helpers. Raise the walls, set the ridge and lift sheets onto the roof with a second person. Keep ladders and sheets at least 10 ft from any overhead power line.
Related plans
- Same 14 ft depth, 2 ft narrower: the 14×16 gable shed plan. 2 ft wider: the 14×20 gable shed plan.
- Same 18 ft front, 2 ft shallower: the 12×18 gable shed plan. 4 ft shallower: the 10×18 gable shed plan.
- Same footprint under a single slope: the 14×18 lean-to shed plan.
- Comparing bases first? Read the shed foundation options guide.
- Every gable shed plan in one place.
Shed building guides
- 6×12 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×10 Firewood Shed Material List: Lumber, Slats, Hardware
- 8×16 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×8 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×16 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×12 Firewood Shed Material List: Lumber, Slats, Hardware
Frequently asked questions
How big and how tall is the 14×18 gable shed?
The eave walls are 18 ft wide and the gable walls are 14 ft deep, 252 sq ft of floor. The top of the walls stands 8 ft 8 1/4 in above the ground and the ridge 12 ft 7 1/16 in, with 12 inch eaves and 4 inch rakes on a 6/12 roof.
Do the 14×18 shed plans include a material list?
Yes. The 73-page PDF has a full shopping list by section, a lumber yard order and a cut list with the length and count of every part. Use them to get a quote from your local lumber yard, since the plan does not price the materials.
Will a riding mower fit in the 14×18 shed?
The plan's drawing parks a mower with a 42 inch deck through the 72 inch double door, about 5 ft 11 1/2 in wide with both leaves open, with 8 1/8 in to spare on each side. A 48 inch deck fits with its deflector raised. A 54 inch deck does not.
Can two people build the 14×18 shed, and how long does it take?
Yes. The plan builds the 18 ft front and back walls in two sections each, so two people can raise every piece. The heaviest lift is a 14 ft side wall at about 190 lb. The plan estimates about 100 hours of work for two people.
What is in the free 14×18 shed plan PDF?
The free preview is 8 pages and shows the drawing style, the five build stages and the finished shed. The full 73-page plan adds the shopping list, the cut list and every dimensioned drawing, and it went through 116 cross-checks before sale.
More about the 14×18 gable shed plan
Build Your Own 14×18 Gable Storage Shed With Ease!
Imagine if you were able to add that much needed 14×18 Gable Storage Shed Plan to your yard with about 48 hours of work for two people? Wouldn’t that be a dream come true? The shed would be spacious enough to store your appliances, tools and hardware. Who would have thought it would be this easy and cost-effective to build a 14×18 Gable Storage Shed all by yourself? If so, then wait no more – order now and start building today…
Shed Plan Includes:
A Full-Fledge Material List with Required Quantity
The materials you use to build a shed are the secrets to your success. Unfortunately, most plans out there won’t precisely tell you what to buy and in what quantity. In fact, they would lure you to buy products from the plan-sellers. Luckily, we have a completely different motto. We want you to succeed in building your dream shed. And for that, we understand how important it is to get the right materials.
Our 14×18 Gable Storage Shed Plan comes with an all-inclusive list of materials, hardware and tools that you would need to build the shed. Nothing more, nothing less! No click baits! You get a printable list of materials that you can take to the hardware store.
Shed Plan Includes:
Simple, Easy to Understand Step by Step Instructions
Who would have ever thought to get their hands on a shed plan that would take them through the entire process with such ease! The 14×18 Gable Storage Shed Plan comes with easy to understand, step by step instructions for DIY newbies. Don’t worry if you don’t have any experience in building wooden structures. The plan takes you through it in plain words, without jargon. Right from building the foundation to the walls and even the roofing, we have everything covered for you.
Shed Plan Includes:
3D Rendered Images for Reality Check
2D images are a thing of the past! Our 14×18 Gable Storage Shed Plan comes with 3D rendered images, which means you get to see every corner, every angle and every inch clearly as if it is being right in front of you by a professional. You won’t have to scratch your head thinking how the shed should from the front, back or the sides. Even the rooftops are visualized in 3D for better understanding.
Building Your Own Shed vs. Getting Professional Help
1st Reason
You Save What a Builder Would Charge
Probably the most important reason for building your own shed is that you save money. A builder charges for labor on top of the materials, for work you can do yourself. With our 14×18 Gable Storage Shed Plan, you get clear instructions, material lists and diagrams to go through the process easily.
2nd Reason
Choose Your Own Design and Make Your Dream Come True
Don’t fall for the marketing gimmicks of most professionals out there. When you start building your own shed, the world is out there for you to explore. With our material list and instructions, you will realize that you can build your dream shed without any design restrictions. The plan is simple yet it gives you the liberty to add in your own flavor!
3rd Reason
You Will Reclaim Your House Again
The 14×18 Gable Storage Shed has 100 sq ft of floor for your storage. Whether you garden or play sports, you can use the shed to keep all sorts of your equipment and tools. Besides, the shed will add an exquisiteness to your garden while fulfilling its purpose.
All the Other Reasons
This Is Exactly What You’ll Get with Your 14×18 Gable Storage Shed Plan!
19 step-by-step sections that guide you through the whole process.
Designed for beginners as well as for professionals.
Explanatory 3D images so you can see exactly what to do next.
Comprehensive materials list that gives you exactly what you need.
Your plan will look great on any mobile device.
PRO-TIPS throughout the build.
High quality PDF plan with everything you need emailed to you instantly.
How to Build a 14×18 Gable Shed: The Steps at a Glance
This is a short overview of how the 14×18 gable shed goes together. The full plan PDF has 19 build steps on 73 pages, with the cut length and count of every part, a shopping list with quantities and drawings for the steps.
Step # 1: Check the Rules Where You Live
Rules for sheds, such as size limits, setbacks and permits, vary by town and HOA. Check your local permit office before you build.
Step # 2: Know the Size of Your 14×18 Shed
The shed is 18 ft wide and 14 ft deep (252 sq ft of floor). The walls are 94 1/2″ tall including the plates, with a 6/12 roof. The roof peaks about 12′ 7 1/16″ above the ground. It has a double door in the front wall and 2 windows (36″ by 36″ rough openings). The plan estimates about 100 hours of work for two people.
Step # 3: Get the Tools and Materials
You need basic carpentry tools: a circular saw, a speed square, a drill/driver, a framing hammer or nailer, a 4 ft level and a tape measure. The main materials are pressure-treated 4×4 skids and 2×6 floor joists, 3/4 in tongue and groove plywood, 2×4 studs, 5/8 in T1-11 siding, 2×6 rafters, 7/16 in OSB, roofing felt, drip edge and asphalt shingles. The plan’s shopping list gives the quantity of each.
Step # 4: Build the Foundation and Floor
Lay a compacted gravel pad and set the pressure-treated 4×4 skids level in both directions. Build the floor frame from pressure-treated 2×6 joists about 15 7/16 in on center, square it by measuring the diagonals, fix it to the skids, then glue and screw the 3/4 in tongue and groove plywood on top.
Important Tips:
- Build the foundation where the shed will stand. Moving a finished shed is hard work.
- Clear plants and loose soil so the pad sits on flat, firm ground.
- Crown every skid up. The floor weight will flatten it.
Step # 5: Frame and Raise the Walls
- Frame each wall flat on the floor with 2×4 studs 16 in on center, with headers over the door and window openings.
- The door rough opening is 6′ 0″ wide by 6′ 4 1/2″ tall.
- Raise each wall with helpers (the plan says how many for each wall), check it plumb with a level, brace it and nail the corners together.
- Cover the walls with 5/8 in T1-11 siding. The plan gives the size of every sheet.
Step # 6: Frame the Roof
- Set the 2×8 ridge board at the height shown in the plan.
- Cut the 2×6 rafters from the pattern rafter and set them 16 in on center, in pairs across the ridge.
- Nail the collar ties across the rafter pairs the plan marks.
- Frame the gable ends. The eaves overhang 12″ past the walls and the rakes 4″.
Step # 7: Sheathe and Shingle the Roof
- Nail 7/16 in OSB over the rafters.
- Add roofing felt and drip edge, then the asphalt shingles. Follow the shingle maker’s instructions.
Step # 8: Door, Window and Trim
- Build the door from the plan and hang it.
- Set the windows in their framed openings by the maker’s instructions.
- Add the fascia, soffit and corner trim.
Step # 9: Finishing Touches
- Paint or stain all exposed wood to protect it from the weather.
- Add shelves and hooks to suit what you store.
Want every measurement? The full 14×18 Gable Storage Shed Plan PDF has the shopping list, the cut list and 19 build steps with drawings.
Ready to build the 14×18 gable shed?
$19.99 for the full PDF: every step, cut and board. 30-day money-back guarantee.



