Find your plan

Hip roof · 240 sq ft

10x24 Hip Roof Shed Plan

Build this 10x24 hip roof shed yourself. Every board, cut and step, drawn in 3D across 71 pages.

$19.99 $29.99−33%
  • 30-day money-back guarantee
  • PDF by email right after checkout
  • Visa, Mastercard, Amex, PayPal
  • Full material and shopping list
  • Cut list with every length
  • Step-by-step 3D views, 71 pages
  • Phone, tablet, PC and Mac
As seen oneHow, Houzz, San Diego Fine Woodworkers Association, wikiHow, Redbeacon

This 10x24 hip roof shed plan from 3DSHEDPLANS builds a 240 sq ft storage shed, 24 ft wide by 10 ft deep, with a 6 ft double door, a ramp, a 3 ft square window in each end wall and a 6/12 roof with 12 inch eaves all round. The 71-page PDF has 19 step sections.

Get the full plan PDF for $19.99 or download the free preview

What builders say

A project for me and my son. The plan arrived in my email almost instantly, and everything we needed was included.
Samantha Peeler
We aren't DIY-savvy and needed something simple. The plan was extremely well laid out and easy to follow.
Mark Lewos
A year ago I had only built flat-pack furniture. The plans are simple to follow, and you don't need years of experience.
Paul Thomas
More builder stories

The full plan is $19.99 as an instant PDF download. To see the drawing style first, open the free 10×24 hip roof shed plan PDF.

10×24 hip roof shed plan: the numbers for a site check

Check 10×24 Hip Roof Shed
Walls 24′ 0″ wide x 10′ 0″ deep, 240 sq ft of floor
Roof footprint with overhangs 26′ 1 1/2″ x 12′ 1 1/2″ to the fascia faces (1′ 0″ eaves on all four sides)
Gravel pad 26′ 0″ x 12′ 0″ inside a pressure-treated 4×6 frame, 4″ of 3/4″ stone (5.4 cu yd loose, with the landing in front of the door)
Floor height Top of the deck 9 3/4″ above the ground
Wall height 7′ 10 1/2″ (7′ 6″ studs), top of the walls 8′ 8 1/4″ above the ground
Overall height 11′ 5 5/16″ above the ground, top of the ridge shingles
Roof Hip, 6/12 (26.6 degrees), 2×6 ridge 14′ 1 1/2″ long, 26 2×4 commons, 4 2×6 hips, 2×4 jacks
Door rough opening 6′ 0″ wide x 6′ 4 1/2″ tall, double door centered in the 24 ft front wall, swings out
Window rough openings 2, each 36″ x 36″, one in each 10 ft end wall toward the front
Roof vents 2 static louvers near the top of the back plane, plus a 1/4″ screened gap under the soffit
Ramp Detachable pressure-treated ramp, 6′ 9″ wide, 3′ 6″ out, 1:6 slope
Crew and time Two people, three for one wall lift, about 96 hours

A hip roof overhangs all four walls, so stake out the 26′ 1 1/2″ x 12′ 1 1/2″ roof outline on your lot, not just the walls, and leave room to walk around it with a ladder. The ramp and landing reach 7′ 2 1/2″ out from the front wall, and the plan’s fit page says to keep 10′ 0″ clear and level in front of the wall (the ramp and one mower length) if you need to line up a tractor square.

How the 10×24 hip roof shed goes together

Stage What the plan uses Time for two
Site and foundation Compacted gravel pad in a 4×6 frame, four 24 ft pressure-treated 4×4 skids, each spliced from an 8 ft and a 16 ft board 8 h
Floor frame and deck Pressure-treated 2×6 joists 16″ on center between spliced rims, 3/4″ tongue and groove plywood 10 h
Walls 2×4 studs 16″ on center or closer, raised as bare frames (the front and back walls in two sections each), then sided with 5/8″ T1-11 24 h
Roof framing 2×6 ridge on two temporary posts, 2×4 commons and jacks, 2×6 hips, rafter ties, king tie 16 h
Sheathing and roofing 7/16″ OSB, drip edge, 15 lb felt, 2 roof vents and 3-tab asphalt shingles 20 h
Door, windows and trim T1-11 double door, 2 prefabricated windows, fascia, sloped soffit, 1×4 trim, paint 18 h

The plan runs in a fixed order: preparation and ground breaking (step 9), skids (10), floor frame (11), decking (12), anchoring the shed (13), the four walls (14 to 17), joining them (18), the door (19), the roof framing plan (20), commons and ridge (21), hips (22), jacks (23), fascia and soffit (24), sheathing, vents and shingles (25), trim, windows and finish (26) and the ramp (27). Section 28 covers weather, snow and upkeep, and a printable checklist lists each stage with “date done” and “checked by” columns.

Site layout, gravel pad and skids

Stake the corners 24′ 0″ along the front and 10′ 0″ along the sides, and move one stake until both diagonals read 26′ 0″. The plan has you dig 4″ deep over a 26′ 11″ x 12′ 11″ area, the outside of the pad frame, and on out in front of the door for the ramp and a 3 ft landing: 9′ 8″ wide, centered on the door, reaching 7′ 2 1/2″ out from the front wall. Digging moves the stakes, so set them again and recheck. On a sloped yard the plan shows how to measure the fall with a string and line level first, and when to build the stone up or dig the high side down.

The frame is pressure-treated 4x6s laid flat, rated for ground contact (UC4A or higher), on a 1/2″ stone bed so it finishes level with the lawn. Its inside is the 26′ 0″ x 12′ 0″ pad plus a landing 8′ 9″ wide that reaches 5′ 9″ past the front of the pad. The back is two 13′ 5 1/2″ pieces butted end to end, the sides are 12′ 0″ each, and the front is two 8′ 7 1/2″ pieces, one each side of the landing, which has 5′ 9″ sides and a 9′ 8″ front. Square it until both pad diagonals read 28′ 7 5/8″, join each corner with 2 galvanized 10″ timber spikes, pin it with 34 rebar stakes, then fill it with 4″ of 3/4″ crushed stone compacted in two layers. The cutting plan gets every frame piece out of one 10 ft and six 16 ft 4x6s.

Four ground-contact pressure-treated 4×4 skids run along the 24 ft side, the outer two flush with the floor edges and the others 3′ 2 13/16″ on center (2′ 11 5/16″ clear between neighbors). A 24 ft skid is longer than a 16 ft board, so each one is spliced from two whole boards, a 16 ft and an 8 ft, with their factory ends kept. Counting from the front, skids 1 and 3 are 8′ 0″ + 16′ 0″ from the left end, and skids 2 and 4 are 16′ 0″ + 8′ 0″. That puts the joints at 8 ft and 16 ft, alternating from skid to skid, each centered under a floor joist. Each joint butts on the gravel with a 3 ft pressure-treated 2×4 scab on both sides, six nails per scab. Set every skid crown up and level it along its length and against the others, with gravel or treated shims under a low one, never untreated wood.

Floor frame and decking

The floor frame is nineteen 9′ 9″ joists between two 24′ 0″ rims, all pressure-treated 2×6, at 16″ on center. Clamp the rims together and mark both at once from the building’s left end: a joist flush at each end, then lines at 15 1/4″, 31 1/4″, 47 1/4″ and every 16″ on. The rafter marks later start from the same corner.

Each rim is longer than a 16 ft board too, so it is cut as 11′ 11 1/4″ + 12′ 0 3/4″. Both rims break at 11′ 11 1/4″ from the left end, over a doubled joist: a twentieth joist on the list is nailed tight against the left face of the layout joist there, so the joint falls on the seam between the two and each rim end gets three nails into a full joist.

Once nailed the frame weighs about 530 lb and racks out of square if you lift it, so you build it in place on the skids, push it until both diagonals read 26′ 0″, then toe-nail it down. A framing angle goes at every joist-to-skid crossing, 80 in all, with 8 connector nails each. On the outer skids the rim covers the joist end, so those angles sit against the inside face of the rim, right beside each joist.

Nine sheets of 3/4″ tongue and groove plywood cover the deck in three rows, cut to a lettered map (pieces A to J). You start at the front left corner with piece A, 7′ 11 7/8″ x 4′ 0″, and the second row starts with piece D, 3′ 11 7/8″ long, so the end joints are staggered and land on joists. With sheets that cover 47 1/2″ once the tongue is in its groove, two full rows cover 7′ 11″ of the 10 ft frame, and the last row is 2′ 1″ wide, ripped as full 8 ft strips. Because that narrow row still flexes at its end joints, the plan adds flat 2×4 blocks between the joists under the seam 7′ 11″ from the front edge (cut from three 8 ft 2x4s) and both sheet edges screw down to them. Pieces G and D share one sheet; every other piece takes a sheet of its own.

Anchoring the shed before the walls go up

The plan figures that, empty, this 11′ 5 5/16″ tall shed on loose skids slides at about 10 psf of wind (gusts near 55 mph) and tips at about 18 psf, and that the bare walls and the sided box catch that wind for days before the roof is on. So in step 13, right after the deck, you set 10 screw-in auger ground anchors, 30″ or longer, with galvanized straps, 5 along each outside skid. Measured from the left end, the front skid’s anchors sit at 1′ 0″, 6′ 3″, 12′ 0″, 17′ 6″ and 23′ 0″, and the back skid’s at 1′ 0″, 6′ 6″, 12′ 0″, 17′ 9″ and 23′ 0″. That keeps them no more than 8 ft apart, and each sits 3″ or more clear of the splice scabs, tight to the skid itself.

An auger will not start in 4″ of compacted stone, so you dig the stone back to the soil at each spot, turn the anchor in with a steel bar through its eye in half turns, and rake the stone back. Each strap runs up the skid’s outside face onto the rim, fastened with 1 1/2″ structural screws, 4 into the skid and 2 into the rim (60 screws in all), and ends at least 3 11/16″ below the deck so the siding, which stops 3 3/16″ below the deck, covers it. The front anchor at 12′ 0″ lands right in front of the door, behind the ramp: the ramp ledger later screws on over its strap, with the screws beside the strap, not through it, and the eye sits between two stringers so the ramp lifts off over it. Check your local permit office for what your area asks.

Walls: framing order and lift weights

Each wall is framed flat on the deck at its own edge, checked by its diagonals and raised as a bare frame. The 24 ft front and back walls are framed and raised in two sections each. The siding goes on after all four walls stand.

Order Wall Studs at 7′ 6″ Bare frame weight
1 Back wall, 24 ft, no openings, 2 sections (12′ 0 3/4″ and 11′ 11 1/4″ from its right corner) 22 (including 2 joint studs and 2 corner backers) About 140 lb each, 2 people each
2 Front wall with the door, 2 sections (15′ 11 1/4″ and 8′ 0 3/4″ from its left corner) 19 (including 2 kings, 2 joint studs and 2 corner backers, plus 2 trimmers and 5 cripples) About 200 lb (the heaviest lift, 3 people) and 100 lb (2 people)
3 Left wall with a window 8 (including 2 kings) About 150 lb, 2 people
4 Right wall with a window 8 (including 2 kings) About 150 lb, 2 people
  • Anchors first. The 10 ground anchors go in at step 13, before any wall goes up, so every wall you raise stands on a floor that cannot slide.
  • The long front section takes three. The first front section runs 15′ 11 1/4″ and holds the whole door opening, so it weighs about 200 lb. The plan has all three people lift it, one near each end and one in the middle, then two hold it while the third nails the braces. If a lift feels like too much, the plan says to set it down and get another person.
  • Sections side by side. Each section has its own plate pieces and a joint stud at the end that meets the next. You raise section 1 first, then the next tight against it, clamp the two joint studs flush and nail them together every 12″, staggered.
  • Stop blocks at the edge. Two 12″ 2×4 offcuts nailed to the rim for each section, 2″ above the deck, keep each bottom plate from kicking out over the edge as it tips up.
  • Nobody in front. A wall that goes past plumb falls outward, off the deck, so nobody stands on the ground in front of it. Pick a calm day and brace it at once, from the outside, with 12 ft 2x4s to stakes about 5 ft out.
  • End walls drop in. Their plates are 9′ 4 3/4″, 1/4″ shorter than the gap between the front and back walls, so plumb those first. Each end wall is pushed tight to the front wall, and the gap stays at the back corners, where it gets a shim at each screw.

The section diagonals are 14′ 4 1/16″ and 14′ 2 13/16″ on the back wall, 17′ 8 11/16″ and 11′ 2 3/16″ on the front, and 12′ 2 1/8″ for each end wall. Each section also gets a tacked diagonal brace before it moves, sawn off flush with the plates so it does not catch the deck edge. The corners are screwed from inside with 3″ exterior screws every 12″. The second top plates (23′ 5″ on the front and back, each from a 7′ 8 1/2″ and a 15′ 8 1/2″ piece, and 10′ 0″ on the ends) lap every corner, and on the long walls they bridge each section joint by at least 4′ 0″ on each side. Each T1-11 sheet (about 60 lb) stands on a 2×4 ledger while your helper holds it plumb. On the front and back the sheet joints fall at 4′ 0″, 8′ 0″, 12′ 0″, 16′ 0″ and 20′ 0″ from the corner, and on the ends at 3′ 0″ and 7′ 0″, each on a stud. Before a wall is sided, its plumb braces move inside (cut to 8′ 7″, the foot on a deck cleat about 3′ 5″ out), and they come off as soon as that wall is sided.

Door and windows: sizes and positions

The door opening is 6′ 0″ wide and 6′ 4 1/2″ tall, from 9′ 0″ to 15′ 0″ measured from the left corner, so it sits centered with 9′ 0″ of wall each side. It sits under two 6′ 3″ 2x8s with 1/2″ plywood between them. Once the bottom plate is cut out the framed height is 6′ 6″, with 6′ 5 1/4″ clear under the head stop.

The two leaves come from two new T1-11 sheets, because the cut-out is too short. Each is 2′ 11 5/8″ wide and 6′ 5 1/4″ tall, with a glued and screwed 1×4 frame: two 6′ 5 1/4″ stiles and three 2′ 4 5/8″ rails, the middle one centered 3′ 2 5/8″ from either end so both bays are 2′ 9 3/8″. Two Z braces per leaf, 3′ 5 5/16″ along either edge, are cut with the miter saw at 36 degrees and rise from the hinge side toward the latch side. Three T-strap hinges hang each leaf on 1/4″ carriage bolts with the nuts inside, so nobody can unscrew the door from outside. The left leaf is active, with the latch on the middle rail 3′ 3 1/8″ above the deck; the right leaf closes on two barrel bolts and carries a 6′ 4 3/4″ 1×2 astragal.

Brush sweeps (2′ 11 1/16″ and 2′ 10 13/16″) close the gap under the leaves, and an aluminum threshold cap, cut to 6′ 0″, covers the deck edge with no threshold board, so wheels roll straight in. A 10″ hook and eye, 36″ above the deck, holds each open leaf against the front wall in wind, its eye in the stud 8 3/8″ past the leaf’s free edge. Open, the left leaf rests on its pull handle about 2 1/2″ off the wall and the right on its latch catch about 1 1/4″ off, so the plan says to fit the hardware first and mark the hook where the leaf really rests.

The windows are prefabricated units for 36″ x 36″ rough openings, one in each 10 ft end wall toward the front: 1′ 11″ to 4′ 11″ from the front end of the right wall’s plate, and 4′ 5 3/4″ to 7′ 5 3/4″ from the back end of the left wall’s 9′ 4 3/4″ plate, which puts both 1′ 11″ from the front end of the plate. Each sill top is 3′ 6″ above the bottom plate, under a header of two 3′ 3″ 2x6s with plywood between. Each opening is wrapped with flashing tape, and a drip cap goes over every head casing: 6′ 9″ over the door and 3′ 9″ over each window.

What is on the 10×24 hip roof shed material list

The shopping list is split by section, so you can buy the base first and the roof later:

Section Main items and counts
Foundation and floor 4 pressure-treated 4×4 x 8 ft and 4 x 16 ft for the spliced skids, 2 pressure-treated 2×4 x 14 ft for the 8 splice scabs, 20 pressure-treated 2×6 x 10 ft for the joists, 2 x 12 ft and 2 x 14 ft for the spliced rims, 9 sheets of 3/4″ tongue and groove plywood, 5.4 cu yd of stone, the pad frame (one 10 ft and six 16 ft pressure-treated 4x6s) with 34 rebar stakes and 16 timber spikes
Walls 2×4 plates and studs for four walls, a doubled 2×8 door header from one 14 ft board, two doubled 2×6 window headers, 18 sheets of 5/8″ T1-11; the header fillers are ripped from a soffit plywood sheet, so the plan says to buy that sheet with the walls
Roof framing 26 commons from thirteen 14 ft 2x4s, a 2×6 ridge from a 16 ft board, 4 2×6 x 10 ft hips, 24 jacks, 12 rafter ties, two king tie pieces, two temporary 12 ft 2×4 ridge posts with 4 braces
Roof covering 16 sheets of 7/16″ OSB (15 plus 1 spare), 2 static roof vents, 2 rolls of 15 lb felt, 16 bundles of 3-tab shingles (starter and caps included), 9 pieces of drip edge
Fascia, door, windows and trim 6 1×6 x 14 ft for the fascia, 4 sheets of 1/2″ plywood for the soffit, 2 new T1-11 sheets for the leaves, 6 T-strap hinges with 18 carriage bolts, a handle and latch, 2 barrel bolts, 2 sweeps, 2 hold-open hooks, a threshold cap, 2 prefabricated windows, 1×4 casing and corner trim, 2 drip caps
Ramp 2 pressure-treated 2×10 x 8 ft for the stringers, 4 pressure-treated 2×6 x 14 ft for the 8 deck boards, a pressure-treated 2×4 ledger and filler, 2 hook-and-eye latches, 145 deck screws, 12 structural screws, 4 rolls of grit tape
Hardware and finish 37 lb of 16d framing nails, siding, sheathing and roofing nails, 54 hurricane ties (skewable ones at the hip corners), 80 framing angles, 4 strap ties plus a splice strap, 10 ground anchors with 60 structural screws, 11 tubes of adhesive, roofing cement, flashing tape, 2 rolls of insect screen, 6 gallons of paint

The list also counts the temporary pieces people forget: 18 wall braces, 4 ridge post braces, 12 brace stakes, 16 deck cleats and the decking seam blocks. That is why the lumber yard order at the end, which adds every section into one list for the counter, shows more 2x4s than the section lists: 78 eight-footers and 42 twelve-footers against 64 and 22. The extra 14 eight-footers are the seam blocks, post braces, stakes and cleats, and the extra 20 twelve-footers are the wall braces and the two ridge posts. The plan suggests 2 or 3 spare studs for bad boards on top.

Cut list and cutting plan

The cut list gives every part’s lumber, length and count: skids and rims at 24′ 0″ overall, joists at 9′ 9″, studs at 7′ 6″, the ridge at 14′ 1 1/2″, commons at a 6′ 9 7/16″ board, hips at a 9′ 0 13/16″ board, jacks at 2′ 7 9/16″, 4′ 0 3/8″ and 5′ 5 1/8″, tail jacks at 1′ 2 13/16″, rafter ties at 10′ 0″ and the king tie at 10′ 8 5/8″ and 11′ 8 7/8″. Trim, door, ramp and pad frame parts are on it too, and every spliced part lists both pieces.

The cutting plan says which board each part comes from and what is left. Two commons come out of each 14 ft 2×4, four short jacks out of each 12 ft 2×4, two middle jacks out of each 10 ft and two long jacks out of each 12 ft. Each rafter tie uses a 12 ft board and leaves a 1′ 11 7/8″ offcut, and the 8 tail jacks come from those offcuts and the window sill offcuts, so they cost no extra boards. The window cripples come from the trimmer and lower cripple offcuts the same way. The long front and back fascia pieces take one 14 ft 1×6 each, and the end pieces two to a board. The roof sheathing has its own plan: 15 sheets cut to a lettered map, the small pieces from the big pieces’ offcuts, plus 1 spare kept whole.

Why the 10×24 hip roof has a 14 ft ridge on two posts

On a square shed the four hips meet at one point. This shed is 24 ft wide and 10 ft deep, so the roof planes on the long walls run up to a ridge instead: a 2×6, 14′ 1 1/2″ long, its ends 4′ 11 1/4″ in from the outside of each end wall. The two long planes are trapezoids and the two end planes are triangles, all at 6/12.

The plan prints the common positions along the front and back plates, measured from the building corner: 5′ 0″, 6′ 3 1/4″, 7′ 6 9/16″ and on to 17′ 8 3/4″ and 19′ 0″. That is twelve pairs across eleven equal bays of about 15 1/4″, plus a king common at the middle of each end wall. Jacks sit at 1′ 3″, 2′ 6″ and 3′ 9″ from every corner, 15″ apart. The roof deck’s joints are cut to land on those centers, so every sheathing joint still lands on a rafter. Hook your tape on the outside corner of the building, not on the end of a plate, because the front and back second top plates start 3 1/2″ in from the corner; the plan also gives each mark as measured on the plate itself.

A ridge this long gets two temporary posts, one about 12″ in from each end. Each 10′ 1 5/16″ 2×4 post stands on the deck on the shed’s center line, its back face 3/4″ behind the line, braced both ways with 2 braces to cleats screwed to the deck. A 12″ cleat, cut from the post board’s offcut, is screwed to the back of each post and stands 4″ above its top, and the ridge sits on the posts tight to the cleats with three screws through each. The posts stay in until every jack is nailed.

How the 10×24 hip roof is framed: ridge, commons, hips and jacks

The plan frames the roof in a fixed order and says who stands where:

  1. Ridge on two posts. The ridge (about 28 lb) goes up with one person at each end, each on an 8 ft step ladder on the deck beside a post, no higher than the third step from the top. Its top sits 2′ 8 5/16″ above the plates and 10′ 6 13/16″ above the deck, a little above eye level from there. Each person screws their own end to the cleat.
  2. Commons in pairs. Cut a pattern common (board 6′ 9 7/16″, top edge 6′ 7 11/16″, seat 2 1/2″, heel 1 1/4″, a notch 32% of the depth), test it on both sides of the ridge, then cut 26: 24 for the front and back and 2 kings. Set the pairs at both ridge ends first, check the ridge for level and center, then fill in one each side so it stays straight. Each common weighs about 9 lb; one person on the ladder by the ridge nails the top, the other on a step ladder at the wall sets the seat and nails the hurricane tie on the common’s left face. The plate is 7′ 10 1/2″ above the deck, so never set or nail a seat from the deck.
  3. Ties and kings. A 2×4 rafter tie, 10′ 0″, goes on the right face of each pair, 12 in all, with its top corners clipped so it stays under the sheathing and four clinched nails into each rafter. The two king commons butt the ridge ends and are toe-nailed to them.
  4. Four hips. Each 2×6 hip runs at 45 degrees in plan from a corner to a ridge end, sloping 19.5 degrees, top edge 1′ 6″ of tail plus 7′ 4 7/8″. Its seat drops 1/4″ so its top corners stay in the roof planes, its top is 2 3/8″ above the plate, both ends get double 45 degree cheek cuts, and the tail is ripped 2 1/16″ to line up with the commons’ soffit. A strap tie goes across the lapped plates at each corner first. Two people set each hip (about 18 lb): one beside the ridge end holds the V point in the corner between the end common and the king, the other inside the wall corner sets the seat.
  5. Jacks, then the posts come out. 24 jacks, centered 1′ 3″, 2′ 6″ and 3′ 9″ from every corner, each about 1′ 4 3/4″ longer than the one before, with 45 degree side cuts in two hands, 4 of each per length. Nail them in pairs either side of a hip, then back out the cleat screws and take the posts out. Eight tail jacks fill the eave between each hip tail and the first jack.
  6. King tie. With the posts out, a 2×4 on edge runs from king to king on top of the rafter ties, in two pieces (10′ 8 5/8″ and 11′ 8 7/8″), each starting 9 1/4″ in from its end wall. They butt over the middle of the rafter tie 11′ 5 7/8″ from the left corner and are joined with a 24″ strap. The rafter ties hold the long walls; this holds the end walls.

The hip seat notch is 3 7/16″ of a 5 13/16″ plumb depth, 59%, far past the one-third the commons keep. The plan explains in step 22.4 that the seat sits right over the lapped plates at the corner, so the notch carries no bending, and the tie, toe-nails and strap hold it. Do not cut it deeper than drawn. Our hip roof shed framing guide walks through the same sequence in more detail.

Fascia, soffit, sheathing and shingles on a hip roof

A hip roof has eaves on all four sides and no rakes. The front and back fascia each run 26′ 1 1/2″ long point to long point, made from a 12′ 5 1/8″ and a 13′ 8 3/8″ piece joined with a 45 degree scarf centered on the rafter tail 11′ 4 3/8″ from the left corner. Each end fascia is 12′ 1 1/2″, two 6′ 0 3/4″ pieces scarfed over the tail 5′ 0″ from the front corner. All four miter at 45 degrees over the hip tails. The 12 plywood soffit strips are 1′ 0 7/16″ wide, ripped from 4 sheets, and slope with the rafter tails over a strip of insect screen. They meet at the corners on a cut line at 48.2 degrees to the strip’s edge, not 45, because they are sloped: measure 11 1/8″ along the wall edge and cut with the circular saw.

The roof is about 349 sq ft. Each long plane is cut from seven pieces (A to G) and each end from three (H, I and J up to the point), and the back and second end are mirror images, laid from the building’s left corner too so their joints land on the same rafters. The drip edge goes on all four eaves before the felt, folded around each corner, and the felt runs from the eaves up with 2″ head laps and 4″ end laps, wrapping 6″ over each hip and the ridge. This roof takes 2 rolls and 9 pieces of drip edge.

Shingles run 16 courses up each plane at 5″ exposure, over a starter strip on all four eaves. Where a course meets a hip, let it run past, snap a line along the hip and cut it off from the top. About 122 cap pieces, cut three to a shingle from 41 shingles, cover the hips from the eaves up, and the ridge is capped last, starting at the end away from the prevailing wind, so its first pieces lap over the hip caps. Total: 16 bundles. The plan says shingle bundles weigh about 60 to 80 lb, so ask the supplier to deliver them onto the roof if they can, or carry half a bundle at a time with one hand always on the ladder.

How the 10×24 hip roof shed is vented

A hip roof has no gable wall for a high vent, so this plan uses two kinds. Air comes in low through a 1/4″ gap left at the siding under the soffit strips, backed with insect screen, all the way around the four eaves. It leaves high through 2 static slant-back louvers, rated 60 sq in of net free area or more, near the top of the back plane, where they face away from the door.

The plan places them in numbers. Counting the back commons from the left end, one vent goes in the bay between the 3rd and 4th commons (8′ 2 3/16″ from the left end wall to the bay center) and one between the 9th and 10th (15′ 9 13/16″). Once the felt is on, you measure 1′ 9″ down from the top of the ridge along the underside of the sheathing and drill a 1/4″ locator hole up through it, centered in the bay. The bay is 1′ 1 3/4″ clear, so no rafter is cut. On the roof you cut the hole with a jigsaw, shingle up to it, set the louver in roofing cement with its lower flange on top of the shingles below, nail only the top and side flanges, and let the next courses lap over them.

The plan also prints its arithmetic and calls it a common attic rule of thumb, not a shed requirement: floor area divided by 150, here 230 sq in, about half low and half high. The two louvers give 120 sq in high, so the high side is met. The soffit gap runs 816″ around the walls and gives about 102 sq in low once the screen is counted, 13.2 sq in short of its half, and 222 sq in in total, 8.4 sq in short. The plan says plainly that the low side is what a 1/4″ gap gives, and that a wider gap lets in more air and more weather. That suits unheated storage. If you plan to heat or insulate the shed, the plan says to ask your local permit office what it wants.

What you can fit in a 10×24 hip roof shed

The plan’s “What fits inside” page draws the room from above, 23′ 5″ across and 9′ 5″ deep inside, with 7′ 7 1/2″ of clear height under the top plates:

  • A 42″ deck riding mower, nose in. With both leaves open the door is about 5′ 11 1/2″ clear, so a 42″ deck (4′ 7 3/16″ wide) clears each side by 8 1/8″. The plan adds that a 48″ deck fits with its deflector raised and a 54″ deck does not. Measure your own mower before you buy.
  • Parked against the back wall. The plan parks the mower’s nose about 1″ off the back wall, between the shelf runs, which leaves about 3′ 6″ of cross aisle behind its tail.
  • A wheelbarrow and two bikes. The drawing also places a wheelbarrow (2′ 2″ x 5′ 0″) and two bikes with their handlebars staggered (2′ 6″ x 5′ 10″) beside the mower.
  • Back-wall shelves, yours to add. There is room for 12″ deep shelves on the back wall in 2 ft runs. They are not on the shopping list.
  • A ramp. The deck sits 9 3/4″ above the gravel, so wheels need the ramp from step 27: 6′ 9″ wide, 3′ 6″ out at 1:6 (9 degrees), eight stringers 11 3/8″ on center under eight 2×6 boards. Its top sits about 13/16″ below the deck, and the leaf swings out over it with 1 1/4″ to spare. Set the mower deck to its highest cut before you take it up. Our guide on how to build a shed ramp covers the idea in general.
  • Headroom under the ties. The rafter ties sit on the plates, 7′ 10 1/2″ above the floor, and the king tie stands on them. Above them the roof is open to the ridge, so stand long items against a wall.

The ramp is cut from four 3′ 6″ pieces of pressure-treated 2×10, each ripped on a taper from 7 1/2″ to 1/2″ so one piece gives two stringers; the plan has you clamp each to two sawhorses and finish the thin end with a handsaw, never holding a short piece by hand. The bottom board is ripped to 2 15/16″ with a 1″ bevel at its toe. The front skid’s splice scab stands 1 1/2″ proud where the ramp goes, so a flat pressure-treated 2×4 filler, notched 1 1/2″ deep for its first 10 1/2″ over the scab, goes on first, and the 6′ 9″ ledger screws on over it with 6 structural screws into the rim and 6 into the skid. Two hook-and-eyes hold the ramp to the ledger, so you can unhook it and lift it away to level or move the shed. An open slot of about 2 5/8″ stays between the top board and the siding; the plan says to keep it swept out and lay a scrap of plywood across it for a small caster or a hand truck.

Hip roof on a 10×24 shed: what it costs you and what it gives

A hip roof takes more cutting than a gable roof: four hips with double cheek cuts and a deep seat, 24 jacks in three lengths and two hands, 8 tail jacks, a king tie in two pieces, soffit corners cut at 48.2 degrees and two vent holes in the back plane. It also covers more roof, about 349 sq ft here under 16 OSB sheets and 16 bundles, because the eave runs around all four sides. The roof framing alone is about 16 hours for two, and the sheathing, felt and shingles another 20.

In return there are no gable triangles to frame and side, no rakes, and an eave over every wall that keeps rain off the siding on all four sides. The roof tops out at 11′ 5 5/16″, only about 2′ 9″ above the 8′ 8 1/4″ top of the walls, which helps where neighbors look at a 24 ft long building. A hip roof generally holds up to wind better than a gable roof, according to the Building America Solution Center guide to hip vs gable roofs. If you would rather frame two flat gable ends, the 10×24 gable shed plan builds on the same footprint, and the 10×24 lean-to shed plan has a single slope.

Tools, ladders and fasteners the plan lists

Beyond a circular saw with a rip guide, a speed square, a framing square, a drill/driver and a framing hammer, the tool list adds:

  • a miter saw for the door braces (set to 36 degrees) and the trim
  • a reciprocating saw or oscillating tool for flush cuts at the threshold and the window openings
  • a jigsaw and a drill with a 1/4″ bit for the roof vent holes and their locator holes
  • a 3 lb sledge for the pad frame spikes and stakes, and two 24″ bar clamps for marking the rims together
  • a 4 ft level, an 8 ft straight board, a string line with a line level and a hand tamper
  • a steel bar or pipe, about 3/4″ x 3 ft, for turning the ground anchors
  • two 8 ft step ladders, which reach the ridge, and a 16 ft extension ladder for roof work from the eave, about 8′ 8″ up; extended it is about 13 ft long and reaches about 4′ 0″ past the edge

The fastener schedule gives the nail and count for every joint, from three 16d nails per joist at the rims to three nails through the side cut of every jack and eight clinched nails at each king tie end. The list counts 37 lb of 16d framing nails, about 1328 nails plus 10%. The corner stud bays are only 8 1/2″ to 1′ 2″ wide, too tight to swing a hammer, which is why the wall corners are screwed from inside. For roof work the plan has you screw a 2×4 foot stop through the sheathing into four or more rafters before you work above it, and never to work on the roof alone.

Free 10×24 hip roof shed plan PDF vs the full plan

The free PDF is a streamlined version: the five stages (site and foundation, floor, walls, roof, trim and paint) with 3D views and framing previews, and a table of what the full plan adds. It has no material list, no cut list and no measurements.

The full 71-page plan adds every step, the spliced skid and rim layouts, every wall section drawn stud by stud with a position table, the roof framing plan with each rafter center, the ridge post figure and its braces, the hip and jack cut marks, the sheathing map and its sheet cutting plan, the roof vent layout, the ramp, the “What fits inside” page, the shopping list and the cut list. It also lists the 110 checks it passed before going on sale, from walls and openings (59 checks) and roof framing (22) to sheets and shingles that cover every surface and drawings that agree with the lists.

Before you build a 10×24 hip roof shed

  • Permits. The plan itself notes that most towns ask for a permit at this size, since 240 sq ft is over the common 120 and 200 sq ft exemptions, and at 11′ 5 5/16″ tall the shed can also run into height or setback limits. Rules vary by town and HOA, so check your local permit office before you buy lumber, and use our shed permit checklist to know what to ask. Call 811 a few working days before you dig.
  • Snow and wind. The plan uses common small-shed framing. In heavy snow or high-wind areas you may need closer rafter spacing or larger rafters; ask your local permit office about the loads for your address before you build.
  • Skids. Use ground-contact rated pressure-treated 4x4s (UC4A or higher), set crown up, and keep the splice joints where the plan puts them. Our gravel shed foundation guide covers the pad in more depth.
  • Crew. Line up a third person for the day the long front wall section goes up, and a helper for the ridge, the commons and the hips. Stand each ladder on firm, flat footing, stay off open rafters until the sheathing is on, keep ladders and sheets 10 ft from overhead power lines and never work on the roof alone.
  • Materials. Store lumber flat and covered, since wet wood decays faster (USDA Forest Products Laboratory Wood Handbook). Check the stamp on each OSB sheet for its span rating (APA: OSB).
  • Upkeep. Keep 6″ or more between the siding and the soil or mulch, keep the drip edges clear, and every spring check for lifted shingles, re-caulk the trim, touch up the paint and make sure the skids are still level and dry.

Related plans

Get 3 shed building tips by email

Short emails over 5 days: site prep, framing mistakes to avoid, and how the full plan saves lumber. Unsubscribe anytime.

Shed building guides

Frequently asked questions

How big is the 10×24 hip roof shed?

The walls are 24 ft wide by 10 ft deep, 240 sq ft of floor. With 12 inch eaves the roof covers 26 ft 1 1/2 in by 12 ft 1 1/2 in to the fascia faces. The ridge tops out 11 ft 5 5/16 in above the ground; check height limits with your local permit office.

Does the 10×24 hip roof have a ridge?

Yes. The shed is 14 ft wider than it is deep, so the four hips meet the two ends of a 14 ft 1 1/2 in 2×6 ridge. While you frame, it sits on two temporary 2×4 posts, each about 12 in in from a ridge end and braced both ways to the deck.

What is on the 10×24 hip roof shed material list?

Every item with its quantity, by section: eight pressure-treated 4×4 boards for four spliced 24 ft skids, 24 pressure-treated 2x6s for the floor, 9 floor sheets, 20 T1-11 sheets, 26 commons, 4 2×6 hips, 24 jacks, 16 OSB sheets, 2 roof vents, 16 shingle bundles, 2 windows, 54 hurricane ties, 10 ground anchors and the ramp lumber.

How long does it take to build the 10×24 hip roof shed?

The plan's stage times add up to about 96 hours for two people: 8 for the site and foundation, 10 for the floor, 24 for the walls, 16 for the roof framing, 20 for sheathing, felt and shingles and 18 for the door, windows, trim and paint.

Will a riding mower fit in the 10×24 hip roof shed?

The fit drawing parks a 42 inch deck rider nose in. With both leaves open the door is about 5 ft 11 1/2 in clear, so that deck clears each side by about 8 1/8 in. A 48 inch deck fits with its deflector raised; a 54 inch deck does not. Measure yours.

How is the 10×24 hip roof shed vented?

Air comes in low through a 1/4 in screened gap under the soffit around all four eaves and goes out high through 2 static roof louvers near the top of the back plane, each rated 60 sq in or more. The plan says this suits unheated storage; if you plan to heat or insulate, ask your local permit office.

More about the 10×24 hip roof shed plan

Build Your Own 10×24 Hip Roof Storage Shed With Ease!

A Hip Roof Shed, as the name implies, looks classy and at the same time can you give your garden or lawn extra space to store your supplies or hardware. Besides, if you are a hobbyist and you want your very own personal space to work, then having a 10×24 Hip Roof Storage Shed is probably the best idea! So wait no more – order now and start building today…

Shed Plan Includes:

A Full-Fledge Material List with Required Quantity

The materials you use to build a shed are the secrets to your success. Unfortunately, most plans out there won’t precisely tell you what to buy and in what quantity. In fact, they would lure you to buy products from the plan-sellers. Luckily, we have a completely different motto. We want you to succeed in building your dream shed. And for that, we understand how important it is to get the right materials.
Our 10×24 Hip Roof Storage Shed Plan comes with an all-inclusive list of materials, hardware and tools that you would need to build the shed. Nothing more, nothing less! No click baits! You get a printable list of materials that you can take to the hardware store.

Shed Plan Includes:

Simple, Easy to Understand Step by Step Instructions

Who would have ever thought to get their hands on a shed plan that would take them through the entire process with such ease! Our 10×24 Hip Roof Storage Shed Plan comes with easy to understand, step by step instructions for DIY newbies. Don’t worry if you don’t have any experience in building wooden structures. The plan takes you through it in plain words, without jargon. Right from building the foundation to the walls and even the roofing, we have everything covered for you.

Shed Plan Includes:

3D Rendered Images for Reality Check

2D images are a thing of the past! Our 10×24 Hip Roof Storage Shed Plan comes with 3D rendered images, which means you get to see every corner, every angle and every inch clearly as if it is being right in front of you by a professional. You won’t have to scratch your head thinking how the shed should from the front, back or the sides. Even the rooftops are visualized in 3D for better understanding.

Building Your Own Shed vs. Getting Professional Help

1st Reason

You Save What a Builder Would Charge

Probably the most important reason for building your own shed is that you save money. A builder charges for labor on top of the materials, for work you can do yourself. With our 10×24 Hip Roof Storage Shed Plan, you get clear instructions, material lists and diagrams to go through the process easily.

2nd Reason

Choose Your Own Design and Make Your Dream Come True

Don’t fall for the marketing gimmicks of most professionals out there. When you start building your own shed, the world is out there for you to explore. With our material list and instructions, you will realize that you can build your dream shed without any design restrictions. The plan is simple yet it gives you the liberty to add in your own flavor!

3rd Reason

You Will Reclaim Your House Again

Our 10×24 Hip Roof Storage Shed has 120 sq ft of floor for your storage. Whether you garden or play sports, you can use the shed to keep all sorts of your equipment and tools. Besides, the shed will add an exquisiteness to your garden while fulfilling its purpose.

All the Other Reasons

This Is Exactly What You’ll Get with Your 10×24 Hip Roof Storage Shed Plan!

19 step-by-step sections that guide you through the whole process.

Designed for beginners as well as for the professionals.

Explanatory 3D images so you can see exactly what to do next.

Comprehensive materials list that gives you exactly what you need.

Your plan will look great on any mobile device.

PRO-TIPS throughout the build.

High quality PDF plan with everything you need emailed to you instantly.

How to Build a 10×24 Hip Roof Shed: The Steps at a Glance

This is a short overview of how the 10×24 hip roof shed goes together. The full plan PDF has 19 build steps on 71 pages, with the cut length and count of every part, a shopping list with quantities and drawings for the steps.

Step # 1: Check the Rules Where You Live

Rules for sheds, such as size limits, setbacks and permits, vary by town and HOA. Check your local permit office before you build.

Step # 2: Know the Size of Your 10×24 Shed

The shed is 24 ft wide and 10 ft deep (240 sq ft of floor). The walls are 94 1/2″ tall including the plates, with a 6/12 roof. The roof peaks about 11′ 5 5/16″ above the ground. It has a double door in the front wall and 2 windows (36″ by 36″ rough openings). The plan estimates about 96 hours of work for two people.

Step # 3: Get the Tools and Materials

You need basic carpentry tools: a circular saw, a speed square, a drill/driver, a framing hammer or nailer, a 4 ft level and a tape measure. The main materials are pressure-treated 4×4 skids and 2×6 floor joists, 3/4 in tongue and groove plywood, 2×4 studs, 5/8 in T1-11 siding, 2×4 rafters, 7/16 in OSB, roofing felt, drip edge and asphalt shingles. The plan’s shopping list gives the quantity of each.

Step # 4: Build the Foundation and Floor

Lay a compacted gravel pad and set the pressure-treated 4×4 skids level in both directions. Build the floor frame from pressure-treated 2×6 joists 16 in on center, square it by measuring the diagonals, fix it to the skids, then glue and screw the 3/4 in tongue and groove plywood on top.

Important Tips:

  • Build the foundation where the shed will stand. Moving a finished shed is hard work.
  • Clear plants and loose soil so the pad sits on flat, firm ground.
  • Crown every skid up. The floor weight will flatten it.

Step # 5: Frame and Raise the Walls

  1. Frame each wall flat on the floor with 2×4 studs 16 in on center, with headers over the door and window openings.
  2. The door rough opening is 6′ 0″ wide by 6′ 4 1/2″ tall.
  3. Raise each wall with helpers (the plan says how many for each wall), check it plumb with a level, brace it and nail the corners together.
  4. Cover the walls with 5/8 in T1-11 siding. The plan gives the size of every sheet.

Step # 6: Frame the Roof

  1. Set the 2×6 ridge and the common rafters that hold it.
  2. Add the four hip rafters from the wall corners to the ridge.
  3. Fill in the jack rafters between the hips and the walls, in matching pairs.
  4. The eaves overhang 12″ on all four sides.

Step # 7: Sheathe and Shingle the Roof

  1. Nail 7/16 in OSB over the rafters.
  2. Add roofing felt and drip edge, then the asphalt shingles. Follow the shingle maker’s instructions.

Step # 8: Door, Window and Trim

  1. Build the door from the plan and hang it.
  2. Set the windows in their framed openings by the maker’s instructions.
  3. Add the fascia, soffit and corner trim.

Step # 9: Finishing Touches

  1. Paint or stain all exposed wood to protect it from the weather.
  2. Add shelves and hooks to suit what you store.

Want every measurement? The full 10×24 Hip Roof Storage Shed Plan PDF has the shopping list, the cut list and 19 build steps with drawings.

Ready to build the 10×24 hip roof shed?

$19.99 for the full PDF: every step, cut and board. 30-day money-back guarantee.

Similar hip roof plans

All hip roof plans