For a 12×24 gable shed on skids, the 12×24 shed material list has 160 framing 2x4s, 24 treated 2x6s for the floor frame, 8 treated 4x4s, 9 sheets of 3/4 in plywood, 13 of OSB, 22 of T1-11 and 15 shingle bundles. It assumes 7′ 10 1/2″ walls and a 6/12 roof.
The list matches the plan line for line: every quantity and cut length on this page is the one printed in the 72-page 3DSHEDPLANS 12×24 gable plan, which has 28 sections and 19 build steps. It counts what to buy by stock length instead of as a board-feet total. The list covers one 72 in double door, two 36 x 36 in windows and a detachable ramp.
What this 12×24 shed material list assumes
The plan is a 24 ft wide by 12 ft deep gable shed, with the ridge along the 24 ft side and 288 sq ft of floor. These are its settings:
- Walls: 7′ 10 1/2″ tall including the bottom plate and double top plate, so wall studs are cut to 7′ 6″ (90 in). The plan buys 47 of the 124 2×4 x 8 ft as full 96 in boards, not 92 5/8 in precut studs.
- Spacing: studs, floor joists and rafters all at 16 in on center.
- Roof: 6/12 pitch, 2×4 rafters, a 2×6 ridge board, 12 in eave overhang and 4 in rake overhang. The roof measures 24′ 9 1/2″ by 14′ 1 1/2″ to the fascia faces.
- Floor: four pressure-treated 4×4 skids, 24 ft long and spliced, 3′ 10 13/16″ on center, on a compacted gravel pad in a pressure-treated 4×6 frame. The floor has 2×6 joists cut to 11′ 9″ at 16 in on center and 3/4 in tongue and groove plywood. The top of the deck sits 9 3/4″ above grade.
- Loads: the plan uses common small-shed framing. Heavy snow or high wind can call for closer rafter spacing or larger rafters, so check your local permit office for the loads at your address.
- Openings: a 72 in wide double door centered in the 24 ft front wall, one 36 x 36 in window in each 12 ft end wall, and a detachable ramp at the door. The 24 ft back wall has no openings.
Our 12×24 gable shed plan is this layout. Our 12×24 lean-to shed plan has the same footprint with a single-slope roof, so its list differs. Use this page to plan your order, and the plan’s own printable list to shop.
Shopping list by stage: the full 12×24 shed material list
Lumber sizes are nominal. A 2×4 measures about 1 1/2 x 3 1/2 in, as the American Wood Council explains. Check the grade stamp on plywood and OSB; the APA trademark guide shows how to read it. Treated lumber that touches the gravel or the ground (skids, scabs, pad frame, ramp) must be rated for ground contact (UC4A or higher).
Totals at a glance
| Material | Total |
|---|---|
| 2×4 framing boards, all lengths | 160 |
| 2×4 x 12 ft for temporary braces and a ridge post | 23 |
| 2×4 x 8 ft for brace stakes and deck cleats | 7 |
| Pressure-treated 2×4 (2 at 14 ft for skid scabs, 2 at 8 ft for the ramp) | 4 |
| Pressure-treated 2×6 for the floor frame (22 at 12 ft, 2 at 14 ft) | 24 |
| Pressure-treated 2×6 x 14 ft for the ramp deck | 4 |
| Pressure-treated 4×4 (4 at 16 ft, 4 at 8 ft) | 8 |
| 2×6 (2 at 8 ft, 1 at 12 ft, 1 at 14 ft) | 4 |
| 2×8 x 14 ft (front header) | 1 |
| 3/4 in T&G plywood sheets (floor) | 9 |
| 7/16 in OSB sheets (roof) | 13 |
| 5/8 in T1-11 sheets (18 walls, 2 gables, 2 door leaves) | 22 |
| 1/2 in plywood sheets (soffit and header fillers) | 3 |
| 3-tab shingle bundles | 15 |
The 160 framing boards are 117 at 8 ft, 3 at 10 ft, 14 at 12 ft, 22 at 14 ft and 4 at 16 ft. With the 23 temporary braces, the 4 stake boards and the 3 cleat boards, the lumber yard order for 2x4s is 124 at 8 ft, 3 at 10 ft, 37 at 12 ft, 22 at 14 ft and 4 at 16 ft: 190 in all.
Floor
| Item | Qty | Used for |
|---|---|---|
| Pressure-treated 4×4 x 16 ft, ground contact | 4 | Long piece of each 24′ 0″ skid |
| Pressure-treated 4×4 x 8 ft, ground contact | 4 | Short piece of each 24′ 0″ skid |
| Pressure-treated 2×4 x 14 ft, ground contact | 2 | Eight 3′ 0″ scabs, one on each side of every skid joint |
| Pressure-treated 2×6 x 12 ft | 22 | 19 floor joists and 1 second joist at the rim joint, all 11′ 9″; 2 rim pieces at 11′ 11 1/4″ |
| Pressure-treated 2×6 x 14 ft | 2 | Rim pieces at 12′ 0 3/4″ |
| 3/4 in T&G plywood, 4×8 sheet | 9 | Floor decking |
| 1×4 x 8 ft | 3 | Decking filler strips, ripped to 1 1/2″ |
| Crushed stone 3/4 in, loose | 6.2 cu yd | Gravel pad, measured loose before tamping |
| Pressure-treated 4×6 x 16 ft, ground contact | 6 | Gravel pad frame |
| Pressure-treated 4×6 x 10 ft, ground contact | 1 | Gravel pad frame |
| Rebar stakes 1/2 in (#4) x 24 in | 36 | Pad frame |
| Galvanized timber spikes 3/8 x 10 in | 16 | Pad frame corners, 2 per corner |
| Deck screws 2 in (or 6d ring-shank nails) | 8 lb | Decking |
| Construction adhesive, 10 oz tube | 13 | A bead on each joist under the decking |
Walls and roof framing
| Item | Qty | Used for |
|---|---|---|
| 2×4 x 8 ft | 117 | Wall studs, cripples, sills, rafters, fly rafters, gable studs, frieze blocks, gable plate ties, short cap plate pieces |
| 2×4 x 10 ft | 3 | Front wall plate pieces, one gable end stud |
| 2×4 x 12 ft | 14 | Back wall plate pieces, side wall plates and cap plates, collar ties, one gable end stud |
| 2×4 x 14 ft | 22 | Rafter ties, trimmers, back wall plate pieces |
| 2×4 x 16 ft | 4 | Front wall plate pieces, front and back cap plate pieces |
| 2×6 x 8 ft | 2 | Window headers |
| 2×6 x 12 ft | 1 | Ridge board, short piece |
| 2×6 x 14 ft | 1 | Ridge board, long piece |
| 2×8 x 14 ft | 1 | Front header |
| Hurricane ties, H2.5A type or equal | 34 | Rafter to plate |
| Framing angles, A34 type or equal | 8 | 4 end rafters at the corners, 4 gable plate ties |
| Temporary braces 2×4 x 12 ft | 18 | Two plumb braces per wall section and the diagonal, reused later |
| Temporary braces 2×4 x 12 ft | 4 | Center gable studs |
| Temporary ridge post 2×4 x 12 ft | 1 | Under the ridge joint, reused later |
| 2×4 x 8 ft | 4 | 12 brace stakes, 24 in, pointed |
| 2×4 x 8 ft | 3 | 16 deck cleats, 12 in |
| Connector nails 1 1/2 in | 5 lb | Hurricane ties, straps and framing angles |
The three header filler strips of 1/2 in plywood are ripped from the soffit sheets, so buy the soffit plywood with the wall lumber. Add 2 or 3 spare studs for bad boards; the plan’s order leaves them out.
Roof covering
| Item | Qty | Used for |
|---|---|---|
| 7/16 in OSB, 4×8 sheet | 13 | Roof sheathing |
| 15 lb felt, 400 sq ft roll | 2 | Underlayment |
| 3-tab shingles, 26 per bundle | 15 bundles | Roof, starter course and ridge cap |
| Drip edge, 10 ft | 10 | Eaves under the felt, rakes over it |
| Roofing nails 1 1/4 in galvanized | 12 lb | Shingles and drip edge |
| Roofing cap nails 1 in | 2 lb | Felt |
| Roofing cement, 10 oz tube | 2 | Last cap pieces and exposed nail heads |
| Louvered gable vent 12 x 18 in, 59.4 sq in net free area or more | 2 | One in each gable |
| Under-eave vent 16 x 8 in, aluminum, screened, 56 sq in net free area or more | 8 | 4 in each eave soffit |
| Insect screen, 2 ft x 25 ft | 1 roll | Behind the vent holes and the soffit vent gaps |
| Staples 3/8 in | 1 box | Insect screen |
Siding and trim
| Item | Qty | Used for |
|---|---|---|
| 5/8 in T1-11, 4×8 sheet | 18 | Walls |
| 5/8 in T1-11, 4×8 sheet | 2 | Gable triangles |
| 5/8 in T1-11, 4×8 sheet | 2 | Door leaves (one per leaf; the cut-out is too short) |
| 1/2 in plywood, 4×8 sheet | 3 | Eave soffit strips and the header fillers |
| Z-flashing, 10 ft | 3 | Wall siding to gable siding joint |
| Drip cap (Z-flashing), 10 ft | 2 | Over the door and window head casings |
| 1×6 x 14 ft | 2 | Eave fascia, long piece |
| 1×6 x 12 ft | 2 | Eave fascia, short piece |
| 1×6 x 10 ft | 4 | Rake fascia |
| 1×4 x 16 ft | 2 | Corner trim on the eave walls |
| 1×4 x 14 ft | 3 | Door casing sides, door stiles |
| 1×4 x 8 ft | 13 | Gable-wall corner trim, door head casing, door rails and Z braces, window casing |
| 1×2 x 8 ft | 2 | Door stop and astragal |
| Exterior paint and primer in one | 7 gal | Two coats of about 828 sq ft each |
| Exterior caulk | 3 tubes | Trim joints and casings |
| Siding nails 2 1/2 in (8d), hot-dip galvanized | 22 lb | T1-11 siding and trim |
| Sheathing nails 2 1/2 in (8d) for OSB | 12 lb | Roof sheathing |
Hardware, door, windows and ramp
| Item | Qty |
|---|---|
| Framing nails 3 1/2 in (16d), hot-dip galvanized (about 1821 nails plus 10 percent) | 51 lb |
| Door hinges, heavy T-strap, 8 in strap or longer, galvanized | 6 |
| Carriage bolts 1/4 x 2 in with washers and nuts (3 per hinge strap) | 18 |
| Door handle and latch set | 1 |
| Barrel bolts for the fixed leaf, 3 in | 2 |
| Door sweep, brush type, 36 in | 2 |
| Door hold-open hook and eye, 10 in galvanized | 2 |
| Aluminum threshold cap, 6 ft | 1 |
| Exterior screws 1 1/4 in (door frame to T1-11; soffit vent flanges) | 1 lb |
| Exterior screws 3 in (hinge T-parts; wall corners where a hammer will not swing) | 1 box |
| Prefabricated window, 36 x 36 in rough opening | 2 |
| Flashing tape 4 in | 1 roll |
| Wood shims | 1 bundle |
| Ground anchors, screw-in auger type, 30 in or longer, with straps | 10 |
| Structural wood screws 1 1/2 in (anchor straps) | 60 |
| Pressure-treated 2×10 x 8 ft, ground contact (ramp stringers) | 2 |
| Pressure-treated 2×6 x 14 ft, ground contact (ramp deck boards) | 4 |
| Pressure-treated 2×4 x 8 ft, ground contact (ramp ledger and filler) | 2 |
| Ramp screws 3 in | 145 |
| Structural screws 5 in, 1/4 in exterior (ramp ledger) | 12 |
| Ramp hook-and-eye latches, 4 in | 2 |
| Anti-slip grit tape, 2 in x 15 ft | 4 rolls |
Cut list highlights
The bulk of the 12×24 cut list is square cuts: 19 front wall studs, 22 back wall studs and 18 side wall studs at 7′ 6″, and 20 floor joists at 11′ 9″. The parts below have angles, overhangs, splices or stacked sizes, and each is cut several times, so one layout error repeats. Lumber varies a little from board to board, so dry-fit the first of each part on your own frame before cutting the rest.
| Part | Lumber | Cut length | Qty |
|---|---|---|---|
| Rafter (board length, see below) | 2×4 | 7′ 10 13/16″ | 38 |
| Fly rafter (rake) | 2×4 | 7′ 10 13/16″ | 4 |
| Ridge board (spliced) | 2×6 | 24′ 8″ | 1 |
| Ridge splice cleat (flat under the ridge joint) | 2×4 | 2′ 0″ | 1 |
| Rafter tie (interior pairs, at the plates) | 2×4 | 12′ 0″ | 17 |
| Gable plate tie (flat under the first 2 rafter ties) | 2×4 | 2′ 6 3/4″ and 2′ 9 3/4″ | 2 each |
| Collar tie | 2×4 | 5′ 6 9/16″ | 9 |
| Lookout block (rake overhang) | 2×4 | 2 1/2″ | 20 |
| Frieze block (over the eave walls, top beveled) | 2×4 | 1′ 0 1/4″, 1′ 1″ and 1′ 1 3/4″ | 2, 32 and 2 |
| Skid (spliced) | PT 4×4 | 24′ 0″ | 4 |
| Skid splice scab | PT 2×4 | 3′ 0″ | 8 |
| Rim joist (spliced) | PT 2×6 | 24′ 0″ | 2 |
| Front and back wall plate (spliced) | 2×4 | 24′ 0″ | 2 each |
| Front and back cap plate (spliced) | 2×4 | 23′ 5″ | 1 each |
| Side wall plate | 2×4 | 11′ 4 3/4″ | 2 each |
| Side wall cap plate | 2×4 | 12′ 0″ | 1 each |
| Front header (2×8 doubled + 1/2 ply) | 2×8 | 6′ 3″ | 2 |
| Front trimmer | 2×4 | 6′ 4 1/2″ | 2 |
| Window header (2×6 doubled + 1/2 ply), each window | 2×6 | 3′ 3″ | 2 |
| Window trimmer, each window | 2×4 | 6′ 6″ | 2 |
| Center gable stud (under the ridge) | 2×4 | 2′ 8 13/16″ | 2 |
| Gable end studs | 2×4 | 11 1/16″, 1′ 7 1/16″, 2′ 3 1/16″ and 2′ 11 1/16″ | 4 each |
| Gable corner nailer | 2×4 | 9 5/8″ | 4 |
| Gable vent sill and header (flat) | 2×4 | 1′ 2 1/2″ | 4 |
Rafters. The 7′ 10 13/16″ figure is the board each rafter needs. Along the top edge alone it is 7′ 9 1/16″, including the 12 in eave overhang, so do not lay out 7′ 10 13/16″ on the top edge. Each rafter takes its own 8 ft board and leaves an offcut of only 1 1/16″, so a mis-cut rafter means a new board.
Plumb cuts are at 26.6 degrees (6/12): set a speed square to 6 on the common scale. The birdsmouth seat is 2 1/2″ with a 1 1/4″ plumb heel, which keeps the notch at 32 percent of the 2×4’s depth, under a third. Cut one pattern rafter, test it on both sides of the shed, then trace the other 37 common rafters. The 4 fly rafters sit on the lookout blocks, not on a wall, so they get the ridge plumb cut but no birdsmouth.
Ridge. The ridge is 24′ 8″, 4 in past each gable wall to carry the fly rafters. It goes up in two pieces, 11′ 0″ from the 12 ft 2×6 and 13′ 8″ from the 14 ft 2×6. The joint is centered on the rafter pair 10′ 8″ from the left corner, with a 2′ 0″ 2×4 cleat flat under it, and the plan stands a temporary 2×4 post under the joint until the rafters on both sides are nailed.
How the 24 ft runs are spliced. Every 24 ft member is two boards, and the plan places each joint so neighbors never line up:
| Member | Pieces | Where the joint lands |
|---|---|---|
| Skids | 8′ 0″ + 16′ 0″ (skids 1 and 3), 16′ 0″ + 8′ 0″ (skids 2 and 4) | Butted on the gravel, centered under a floor joist and 4 ft or more from the joint in the next skid, a scab on each side |
| Rim joists | 11′ 11 1/4″ + 12′ 0 3/4″ (12 ft + 14 ft boards) | Over a doubled joist |
| Front wall plates | 15′ 11 1/4″ + 8′ 0 3/4″ (16 ft + 10 ft boards) | At the section joint, between the two joint studs |
| Front cap plate | 7′ 8 1/2″ + 15′ 8 1/2″ (8 ft + 16 ft boards) | Centered on a stud |
| Back wall plates | 12′ 0 3/4″ + 11′ 11 1/4″ (14 ft + 12 ft boards) | At the section joint, between the two joint studs |
| Back cap plate | 7′ 8 1/2″ + 15′ 8 1/2″ (8 ft + 16 ft boards) | Centered on a stud |
| Ridge | 11′ 0″ + 13′ 8″ | Centered on a rafter pair, with a 2×4 cleat under it |
| Eave fascia | 11′ 0″ + 13′ 8″ (12 ft + 14 ft boards) | Centered on a rafter tail |
Tamp the gravel under each skid joint in thin layers until a boot heel leaves no print.
Headers. The 72 in door opening gets a doubled 2×8 header with a 1/2 in plywood filler, on trimmers cut to 6′ 4 1/2″, with five 6 1/4″ cripples above it. The bottom plate is cut out of the doorway after the wall is up, so the door leaves swing over the floor. Each window gets a doubled 2×6 header on 6′ 6″ trimmers, two 6 1/2″ cripples above, a 3′ 0″ sill and two 3′ 4 1/2″ cripples below.
Gable studs. Each 12 ft gable has one 2′ 8 13/16″ center stud plus eight end studs in four lengths (two of each), from 11 1/16″ to 2′ 11 1/16″. The studs under the two roof sides are mirror pieces: the top angle slopes the other way, so hold each one against its own end rafter and mark it before you cut. Cut alike, half come out wrong.
Siding at the rim. On the front and back walls the T1-11 hangs 3 3/16″ below the floor surface and laps 2 7/16″ of the rim, where it is nailed. Keep the lap primed and painted.
Plates. The side walls have 11′ 4 3/4″ bottom and top plates, with 12′ 0″ cap plates that lap over the front and back walls to lock the corners.
Gable vs lean-to: what changes
A single-slope lean-to roof on the same footprint drops the parts that make a gable roof a gable. The skids, joists and decking stay the same. The plan prints no lean-to counts, so this table compares parts, not totals.
| Item | Gable (6/12, this plan) | Lean-to (single slope) |
|---|---|---|
| Rafters | 38 2×4 at 7′ 10 13/16″ + 4 fly | One slope of longer rafters, no ridge |
| Ridge board | 2×6, cut 24′ 8″ from two boards | None |
| Wall studs | 7′ 6″ on all four walls | Different lengths front and back, stepped on the sides |
| Gable triangles | 2 sheets of T1-11 | None |
| Roof OSB sheets | 13 | Fewer, one slope |
| Shingle bundles | 15 | Fewer, one slope |
| Gable vents | 2 | None |
| Extra roof parts | Fly rafters, lookout blocks, collar ties, gable plate ties | None |
| Floor (skids, joists, decking) | 4, 20, 9 sheets | Same footprint, same floor parts |
The lean-to roof has fewer parts: no ridge, no gable triangles, no fly rafters. The walls take more care, since each side wall has studs that step down toward the back under a sloped top plate, and headroom drops toward the back.
At a low pitch, read the minimum slope on the shingle wrapper before you buy. For more on single-slope builds, see how to build a lean-to shed, all lean-to shed plans and our gable vs lean-to vs hip roof comparison.
Where the waste goes
Buying by stock length means every cut leaves an offcut. The plan picks a stock length for each part that leaves room for squaring the ends, so you know in advance where the scraps come from.
- Wall studs: 7′ 6″ from a 96 in board leaves 5 7/8″ each.
- Rafters: 7′ 10 13/16″ from an 8 ft board leaves 1 1/16″.
- Floor joists: 11′ 9″ from a 12 ft board leaves 2 7/8″ for squaring the ends.
- Rafter ties: the seventeen 12′ 0″ ties come from 14 ft boards, leaving 1′ 11 7/8″ each. Keep those ends for the lookout blocks.
- Collar ties: two 5′ 6 9/16″ ties come out of each 12 ft board.
- Ridge and eave fascia: the 13′ 8″ pieces leave 3 7/8″ and the 11′ 0″ pieces leave 11 7/8″.
- Rim pieces: the 12′ 0 3/4″ pieces leave 1′ 11 1/8″ and the 11′ 11 1/4″ pieces leave 5/8″.
- Scabs: four 3′ 0″ scabs per 14 ft treated 2×4 leave 1′ 11 1/2″.
- No trim room: the 16 ft and 8 ft skid boards, the two 12′ 0″ side cap plates and the three decking filler strips are whole boards. Measure these at the yard and check that the factory ends are square.
- Sheets: 9 floor sheets and 18 wall sheets leave no spare. Many tongue and groove panels cover about 47 1/2 in net, so three rows cover 11′ 10 1/2″ of the 12′ 0″ frame. The 3 filler strips ripped to 1 1/2″ fill the last 1 1/2″ along the back rim; check the net face width on your label.
- No spares: the counts include nothing for rejects. Pick straight stock at the yard, and add a few 2×4 x 8 ft if you expect to cull warped or split boards.
Tools and crew for a 12×24 build
- Circular saw with a rip guide, speed square and framing square for the stud and rafter cuts; cut the 2 1/2 in lookout blocks from a long clamped stick with a stop block, never as loose scraps
- Miter saw (or the circular saw and a speed square) for door braces, trim and casing; a reciprocating saw for the doorway bottom plate
- Framing hammer or framing nailer, and a drill/driver for the screws
- 4 ft level, 8 ft straight board, 25 ft tape and a string line for the 24 ft rims and plates
- Hand tamper for the 6.2 cu yd of gravel, laid in thin layers
- Two 8 ft step ladders and a 16 ft extension ladder for the roof, with the eave about 8′ 8″ above the ground
- A crew of two for each lift: the front and back walls go up in two sections each (about 140 lb and 140 lb for the back wall, about 200 lb and 100 lb for the front), and the side walls weigh about 160 lb each as bare frames. The floor frame is never lifted: it weighs about 620 lb once nailed, so you build it in place on top of the skids
Common mistakes
- Mixing up 12×24 and 24×12. In this list the ridge runs along the 24 ft side. Turn it the other way and every rafter, the ridge and the gables change.
- Moving the splices. The plan places every plate, cap, skid and rim joint for you, and it staggers the cap plate joints over the plates below. Move one and you can stack joints into a hinge line in the floor or walls. Do not plan to drag a shed on spliced skids to a new spot later.
- Forgetting the door sheets. The piece cut out of the front wall is too short for a 6′ 5 1/4″ door stile, so each leaf needs its own new T1-11 sheet.
- Skipping rafter ties. A ridge board is not a beam. The 17 rafter ties at the plates stop the 24 ft walls from spreading, and the flat gable plate ties stiffen the top of each gable wall against wind. The 9 collar ties higher up do not replace them.
- Deep birdsmouths. A seat cut for full 3 1/2 in bearing notches too deep into a 2×4 rafter. Keep the seat at 2 1/2″.
- Too few skids. Four skids under a 12 ft deep floor land 3′ 10 13/16″ apart on center. Three would leave a gap over 48 in under the joists.
- Skipping the ground anchors. An empty shed on skids can slide in a strong gust. The list has 10 anchors, 5 along each outside skid.
- Swapping materials without recounting. This list is for 3-tab shingles and T1-11. Architectural shingles, metal roofing or lap siding cover differently, so recount from the coverage printed on the bundle or the maker’s install guide.
- Untreated wood near the ground. Skids, rims, joists and scabs are pressure treated; plain framing lumber there rots. Use ground-contact rated wood for the skids, and hot-dip galvanized nails and treated-lumber rated screws in treated wood. The USDA Wood Handbook covers why wet, untreated wood decays.
A 288 sq ft shed is large enough that permit, setback and tie-down rules matter, and they vary by town, so check your local permit office before you order. Our shed permit checklist lists what to ask.
For how to read any list like this one, see our shed material list guide. For the base under the skids, see shed foundation options. For a rough budget, see how much it costs to build a shed, then price this list at two yards. For other sizes, try the shed material calculator.
Get the full plan
The 12×24 gable shed plan is a 3DSHEDPLANS PDF with 72 pages and 28 sections, 19 of them step-by-step build steps, with drawings, cut details and its own printable material list. The plan prints how long each stage takes for two people (116 hours in all) and the weight of each bare wall frame. For another footprint, the 14×24 gable shed plan and 10×24 gable shed plan share the 24 ft length, and the 12×20 gable shed plan shares the 12 ft depth. Compare the 12×20 shed material list for a shorter build.
Want to see the format first? Download the free 12×24 gable shed plan preview PDF. Need more or less room? Compare all gable shed plans or browse every size on the shed plans page.
Frequently asked questions
What is on a 12×24 shed material list?
For a 12×24 gable shed, the plan lists 160 framing 2x4s, 24 treated 2x6s, 8 treated 4x4s, 9 sheets of 3/4 in plywood, 13 of OSB, 22 of T1-11, 3 of 1/2 in plywood and 15 shingle bundles, plus trim, nails and hardware.
Is there a free 12×24 shed plan with a material list?
This page repeats the paid plan's shopping list and key cut lengths for free. The 3DSHEDPLANS 12×24 gable shed plan is a 72-page PDF with its own printable material list and cut list, and a free preview PDF shows the format first.
How many 2x4s do I need for a 12×24 shed?
160 framing boards: 117 at 8 ft, 3 at 10 ft, 14 at 12 ft, 22 at 14 ft and 4 at 16 ft. The plan adds 23 2x4s at 12 ft for temporary braces and a ridge post, and 7 at 8 ft for stakes and cleats.
How many sheets of plywood, OSB and siding does a 12×24 shed need?
9 sheets of 3/4 in tongue and groove plywood for the floor, 13 sheets of 7/16 in OSB for the roof, 22 sheets of 5/8 in T1-11 for the walls, gables and door leaves, and 3 sheets of 1/2 in plywood for the soffit and the header fillers.
How many bundles of shingles for a 12×24 shed roof?
15 bundles of 3-tab shingles for the 6/12 gable roof with 12 in eaves and 4 in rakes. The plan counts about 385 shingles, including the starter course and the ridge cap.
Shed building guides
- 6×12 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×10 Firewood Shed Material List: Lumber, Slats, Hardware
- 8×16 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×8 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×16 Firewood Shed Material List: Lumber, Slats, Hardware
- 4×12 Firewood Shed Material List: Lumber, Slats, Hardware




